Manual Hitachi FCJ65S3A (page 10 of 52) (English, German, Dutch, French, Italian, Portuguese, Spanish)

566999

Zoom out

Zoom in

1/52

EnglishEnglish

Table 1 List of Appropriate Blades

Material to be cut Material quality Blade No.

Lumber

General lumber

No.1 or No.31 (thick plate) or No.41 (thick

plate) or No.2 (thin plate)

Plywood No.3 or No.6

Iron plate Mild steel plate No.6

Nonferrous metal Aluminum, copper, brass No.6

Phenol resin, melamine resin, etc. No.4 (thick plate) or No.6 (thin plate)

Synthetic resin

Vinyl chloride, acryl resin, etc.

No.2 or No.4 (thick plate) or No.6

(thin plate)

Foamed styrol, etc. No.2

Pulp

Cardboard, corrugated paper No.2

Hardboard No.5 or No.6

Fiberboard No.6

Others

Hard rubber No.2

Slate No.5

2. Acceptable commercial blades (Fig. 14)

This machine is designed to accept most blades

available on the open market. As illustrated in

Fig. 14, blade dimension restrictions are as follows:

⅜ Thickness : L2 ..... Less than 1.6mm

⅜ Width : L3 ..... 6.3mm

L4 ..... 8mm

L5 ..... 7mm

NOTE

When cutting thick materials, use HITACHI genuine blades

which have an inclination as shown in Fig. 4-A or B.

MAINTENANCE AND INSPECTION

1. Inspecting the blade

Continued use of a dull or damaged blade will result

in reduced cutting efficiency and may cause

overloading of the motor. Replace the blade with a

new one as soon as excessive abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool. Exercise due care to ensure the winding

does not become damaged and/or wet with oil or

water.

4. Replacing supply cord

If the supply cord of Tool is damaged, the Tool must

be returned to Hitachi Authorized Service Center for

the cord to be replaced.

5. Servicing

Consult an authorized Service Agent in the event of

power tool failure.

6. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATION

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country specific regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling

instruction, to a Hitachi Authorized Service Center.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

01Eng_FCJ65V3_WE 3/10/09, 19:019

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi FCJ65S3A in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi FCJ65S3A Manual

Product: