382967

Hitachi fcj 55 va Manual

7
Zoom out
Zoom in
Previous page
1/30
Next page
5
English
SPECIFICATIONS
Model FCJ55VA FCJ55
Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)
Power input 400W*
Wood: 55mm
Max. cutting depth
Mild steel: 3mm
No-load speed 0 ~ 3000/min 3000/min
Stroke 18mm
Min. cutting radius 25mm
Weight (without cord) 1.4kg
* Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) Blade No.31 ................................................................. 1
For cutting thick lumber
(2) Splinter guard ............................................................. 1
(3) Chip cover ................................................................... 1
(4) Hexagonal bar wrench ............................................... 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
(1) Blades, No.1 ~ No.6, 31*
* No.31 Blade is a standard accessory.
(2) Guide
(3) Dust collector
Optional accessories are subject to change without notice.
APPLICATIONS
⅜ Cutting various lumber and pocket cutting
⅜ Cutting mild steel plate, aluminum plate, and copper
plate
⅜ Cutting synthetic resins, such as phenol resin and
vinyl chloride
⅜ Cutting thin and soft construction materials
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
MOUNTING THE BLADE
1. Use the accessory hexagonal bar wrench to loosen
the blade set screws on the set ring, as shown in
Fig. 1.
2. Holding the blade with its cutting edge facing the
front, insert the mounting portion of the blade into
the plunger groove until it touches the bottom of the
groove.
3. As shown in Fig. 1, firmly clamp the side screw.
CAUTION
⅜ Loosened set screws may cause the blade to be
damaged. Always ensure that the set screws are
securely tightened. Always ensure that the plunger
groove is clean and clear of sawdust to ensure proper
blade mounting and set screw clamping.
ADJUSTING AND REMOVING THE GUIDE
ROLLER
1. Adjusting the guide roller
The guide roller, shown in Fig. 2, is employed to
prevent the blade from snapping. Prior to use, adjust
guide roller in accordance with the following
procedures:
(1) Loosen the holder set screw with the accessory
hexagonal bar wrench.
(2) Gently slide the guide roller until the roller groove
lightly touches the back of the blade.
NOTE
On delivery from the factory, there is a gap of about
3mm between the roller and blade.
(3) Firmly tighten the holder set screw.
CAUTION
⅜ The guide roller can be used only for Blades that
have a straight line on the rear that is longer than
50mm. (Fig. 3A and 3B) When using other types
of blades (Fig. 3C), slide the guide roller in
backwards so that the guide roller does not contact
the blade.
⅜ When cutting thick boards or performing
continuous cutting operations, use the blade
shown in the Fig. 3A, 3B and be sure to set the
guide roller.
2. Removing the guide roller
The guide roller can be removed from the jig saw
as follows:
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi fcj 55 va at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi fcj 55 va in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 5,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info