566555

Hitachi DV14DSFL Manual

11
Zoom out
Zoom in
Previous page
1/68
Next page
English
11
CAUTION
○ The clutch dial cannot be set between the numerals “1, 3,
5 ... 22” or the dots.
○ Do not use with the clutch dial numeral between “22”
and the line at the middle of the drill mark. Doing so may
cause damage (See Fig. 6).
2. Tightening torque adjustment
(1) Tightening torque
Tightening torque should correspond in its intensity to
the screw diameter. When too strong torque is used,
the screw head may be broken or be injured. Be sure
to adjust the clutch dial position according to the screw
diameter.
(2) Tightening torque indication
The tightening torque diff
ers depending on the type of
screw and the material being tightened.
The unit indicates the tightening torque with the numbers
“1, 3, 5 ... 22” on the clutch dial, and a dots. The tightening
toque at position “1” is the weakest and the torque is
strongest at the highest number
(See Fig. 5).
(3) Adjusting the tightening torque
Rotate the clutch dial and line up the numbers “1, 3, 5 ...
22” on the clutch dial, or the dots, with the triangle mark
on the outer body. Adjust the clutch dial in the weak or the
strong torque direction according
to the torque you need.
CAUTION
○ The motor rotation may be locked to cease while the unit
is used as drill. While operating the impact driver drill,
take care not to lock the motor.
○ Too long hammering may cause the screw broken due to
excessive tightening.
3. Rotation to Impact changeover
(See Fig. 5)
The “Rotation (Rotation only)” and “Impact (Impact +
Rotation)” can be switched by aligning the drill mark “
”
or the hammer mark “
” with the triangle mark on the
outer body.
○ To make holes in the metal, wood or plastic, switch to
“Rotation (Rotation only)”.
○ To make holes in bricks or concrete blocks, switch to
“Impact (Impact + Rotation)”.
CAUTION
○ If an operation which is normally performed at the
“Rotation” setting is
performed at “Impact” setting, the
eff ect of making holes does not only increase but it may
also damage the bit or other parts.
○ If it is hard to turn the clutch dial to hammer mark
“
” position, turn the chuck slightly in either direction
and then turn the clutch dial to hammer mark “ ” position
again.
4. Change rotation speed
Operate the shift knob to change the rotational speed.
Move the shift knob in the direction of the arrow (See
Figs. 7 and 8).
When the shift knob is set to “LOW”, the drill rotates at a
low speed. When set to “HIGH”, the
drill rotates at a high
speed.
CAUTION
○ When changing the rotational speed with the shift knob,
confi rm that the switch is off .
Changing the speed while the motor is rotating will
damage the gears.
○ When setting the shift knob to “HIGH” (high speed) and
the position of the
clutch dial is between “15” and “22”, it
may happen that the clutch does not engaged and that
the motor is locked. In such a case, please set the shift
knob to “LOW” (low speed).
○ If the motor is locked, immediately turn the power off . If
the motor
is locked for a while, the motor or battery may
be burnt.
○ To extend the lifetime, the lithium-ion battery equips with
the protection function to stop the output.Therefore, if the
tool is overloaded, the motor may stop. However, this is
not the trouble but the result of protection function. In
this
case, release the switch of tool and eliminate the causes
of overloading.
5. The scope and suggestions for uses
The usable scope for various types of work based on the
mechanical structure of this unit is shown in Table 4.
Table 4
Work Clutch dial position Suggestions
Drilling
Brick
Use for drilling purpose.
Wood
Steel
Aluminum
Driving
Machine screw 1 – 22 Use the bit or socket matching the screw diameter.
Wood screw
1 –
Use after drilling a pilot hole.
000Book_DV14DSFL_WE.indb 11000Book_DV14DSFL_WE.indb 11 2011/03/23 12:00:472011/03/23 12:00:47
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi DV14DSFL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi DV14DSFL in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info