387424
6
Zoom out
Zoom in
Previous page
1/42
Next page
English
5
4. Mounting and dismounting of the bit.
For Drill chuck with chuck wrench (Fig. 1)
Fit the drill bit into the chuck and use the chuck
wrench to secure it, tightening the chuck by each
of the three holes in turn.
For keyless chuck
The country of use will determine whether Type A or Type
B keyless chuck is required.
Type A (Fig. 2)
(1) Mounting the bit
Turn the lock collar in the direction “AUF” and open
the chuck. After inserting the drill bit into the chuck
as far it will go, turn the lock collar in the “ZU”
direction. Grip the retaining ring and close the chuck
by turning the sleeve clockwise as viewed from the
front.
(2) Dismounting the bit
Turn the lock collar in the direction “AUF” to release
the chucking force. Grip the retaining ring and open
the chuck by turning the sleeve counterclockwise.
NOTE
When the sleeve does not become loose any further,
fix the side handle to retaining ring, hold side
handle firmly, then turn the sleeve to loosen by
hand. (Fig. 4)
Type B (Fig. 3)
(1) Mounting the bit
Turn the sleeve counterclockwise and open the
chuck. After inserting the drill bit into the chuck as
far it will go, grip the retaining ring and close the
chuck by turning the sleeve clockwise as viewed
from the front.
(2) Dismounting the bit
Grip the retaining ring and open the chuck by
turning the sleeve counterclockwise.
NOTE
When the sleeve does not become loose any further,
fix the side handle to retaining ring, hold side
handle firmly, then turn the sleeve to loosen by
hand. (Fig. 4)
Model DV20VB DV20VC DV20T2
Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)
Power input 750W*
Reversible Yes No No
Speed change 1 2 1 2 1 2
No load speed
0–1100 0–2600 0–1100 0–2600 1100 2600
/min /min /min /min /min /min
Steel 13 mm 8 mm 13 mm 8 mm 13 mm 8 mm
Concrete 20 mm 13 mm 20 mm 13 mm 20 mm 13 mm
Wood 40 mm 25 mm 40 mm 25 mm 40 mm 25 mm
Full load impact rate
14000 36000 14000 36000 14000 36000
/min /min /min /min /min /min
Weight (without cord)
Spec. for chuck fitted with chuck wrench 2.3 kg
Spec. for keyless chuck 2.5 kg
STANDARD ACCESSORIES
(1) Chuck Wrench (Spec. only for chuck fitted with
chuck wrench) ........................................................... 1
(2) Side Handle ............................................................... 1
(3) Depth Gauge ............................................................. 1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
(1) Impact Drill Bit (for concrete)
3.2 mm – 20 mm dia.
(2) Drill Stand (Model D10–DS)
Optional accessories are subject to change without notice.
APPLICATIONS
By combined actions of ROTATION and IMPACT:
Boring holes in hard materials (concrete, marble,
granite, tiles, etc.)
By ROTATIONAL action:
Boring holes in metal, wood and plastic.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, inviting serious
accident.
3. Extension cord
When the work area is removed from the power
source. Use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
SPECIFICATIONS
*Be sure to check the nameplate on product as it is subject to change by areas.
Capacity
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi dv 20 t2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi dv 20 t2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi dv 20 t2

Hitachi dv 20 t2 User Manual - English, Danish, Swedish, Norwegian, Finnish - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info