Manual Hitachi dv 18dmr (page 11 of 78) (German, Dutch, French, Italian, Portuguese, Spanish)

386383

Zoom out

Zoom in

1/78

English

CAUTION

⅜ The selection examples shown in Table 5 should be

considered as general standard. As different types of

tightening screws and different materials to be

tightened are used in actual works proper adjustments

are naturally necessary.

⅜ When using the impact driver drill with a machine

screw at HIGH (high speed), a screw may damage or

a bit may loose due to the tightning torque is too

strong. Use the impact driver drill at LOW (low speed)

when using a machine screw.

NOTE

The use of the battery EB1426H, EB1430H, EB1826HL

and EB1830HL in a cold condition (below 0 degree

Centigrade) can sometimes result in the weakened

tightening torque and reduced amount of work. This,

however, is a temporary phenomenon, and returns

to normal when the battery warms up.

7. Mounting and dismounting of the bit

(1) Mounting the bit

Loosen the sleeve by turning it toward the left (in the

counterclockwise direction as viewed from the front)

to open the clip on the keyless chuck. After inserting

a driver bit, etc., into the keyless drill chuck, and

tighten the sleeve by turning it toward the right (in

the clockwise direction as viewed from the front)

(See Fig. 8).

⅜ If the sleeve becomes loose during operation, tighten

it further.

The tightening force becomes stronger when the

sleeve is tightened additionally.

(2) Dismounting the bit

Loosen the sleeve by turning it toward the left (in the

counterclockwise direction as viewed from the front),

and then take out the bit, etc. (See Fig. 8).

Work Suggestions

Brick

Drilling

Wood

Use for drilling purpose.

Steel

Aluminum

Machine screw Use the bit or socket matching the screw diameter.

Driving

Wood screw Use after drilling a pilot hole.

Table 4

When the shift knob is set to “LOW”, the drill rotates

at a low speed. When set to “HIGH”, the drill rotates

at a high speed.

CAUTION

⅜ When changing the rotational speed with the shift

knob, confirm that the switch is off.

Changing the speed while the motor is rotating will

damage the gears.

⅜ When setting the shift knob to “HIGH” (high speed)

and the position of the cap is bitween “16” and “22”,

it may happen that the clutch does not engaged and

that the motor is locked. In such a case, please set the

shift knob to “LOW” (low speed).

⅜ If the motor is locked, immediately turn the power

off. If the motor is locked for a while, the motor or

battery may be burnt.

5. The scope and suggestions for uses

The usable scope for various types of work based on the mechanical structure of this unit is shown in Table 4.

Table 5

6. How to select tightening torque and rotational speed

Use Cap Position

Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Machine screw 1 – 22

For 4 mm or smaller

diameter screws.

Driving

Wood screw 1 –

For 8 mm or smaller nominal

diameter screws.

Brick

For 14 mm or smaller

diameters. (DV14DMR)

For 16 mm or smaller

diameters. (DV18DMR)

Drilling

Wood

For 45 mm or smaller

diameters. (DV14DMR)

For 50 mm or smaller

diameters. (DV18DMR)

Metal

For drilling with a metal

working drill bit.

For 6 mm or smaller

diameter screws.

For 4.8 mm or smaller

nominal diameter screws.

For 10 mm or smaller

diameters. (DV14DMR)

For 12 mm or smaller

diameters. (DV18DMR)

For 20 mm or smaller

diameters. (DV14DMR)

For 22 mm or smaller

diameters. (DV18DMR)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi dv 18dmr in the language / languages: German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,76 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi dv 18dmr

Hitachi dv 18dmr User Manual - English, Danish, Swedish, Norwegian, Finnish - 46 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi dv 18dmr Manual

Product: