387422

Hitachi dv 10 dva Manual

28
Zoom out
Zoom in
Previous page
1/32
Next page
26
English
100
90
80
70
60
50
40
30
20
10
0
10°C
20°C
NOTE
The charging time may very depending on the
ambient temperature and input power supply
voltage conditions.
The example of the relationship between the input
power supply voltage and the charging time is shown
in Fig 9.
The charging time decreasaes if the ambient
temperature and input power supply voltage are
high and increases when they are low.
Fig.9 Relationship Between Input Power Supply
Voltage and Charging Time
CAUTION
If the battery is heated due to direct sunlight, etc.,
just after operation, the charger pilot lamp may
not light. At that time cool the battery first, then
start charging.
3. Disconnect the charger power cord from the AC
outlet.
4. Hold the charger tight and pull out the battery.
PRIOR TO OPERATION
1. Setting up and checking the work environment
Check if the work environment is suitable by fol-
lowing the precautions.
HOW TO USE
1. Confirm the cap position
The three modes of screwdriver, drill and impact drill
can be switched by the position of the cap in this tool.
(1) When the tool is used as a screwdriver, align the
number displayed on the cap from "1" to "5" to the
triangle mark of the housing.
(2) When the tool is used as a drill, align the drill mark
"
" displayed on the cap to the triangle mark of
the housing.
(3) When the tool is used as the impact drill, align the
hammer mark "
" displayed on the cap to the
triangle mark of the housing. (See Fig. 4.)
3. Minus driver bit
a Screw size
0.8 mm 4 mm
a
4. Hexagon socket (for nuts and bolts)
Socket No. Screw size
74 mm
85 mm
10 6 mm
Socket No.
5. Drill bit for brick
Diameter, 6.5 mm, 8 mm, 9.5 mm, 10 mm
Optional accessories are subject to change without notice.
APPLICATIONS
⅜ Drilling of brick and concrete block, etc.
⅜ Driving and removing of machine screws, wood
screws, tapping screws, etc.
⅜ Drilling of various metals.
⅜ Drilling of various woods.
BATTERY REMOVAL/INSTALLATION
1. Battery removal
Hold the handle tightly and push the battery latch
to remove the battery (see Figs. 1 and 2).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 2).
CHARGING
Before using the impact drill, charge the battery as
follows.
1. Insert the battery in the charger.
Position the battery so that the nameplate faces
toward the nameplate of the charger and press in
the battery until it comes into contact with the
bottom plate. (See Figs. 1 and 3.)
2. Connect the charger power cord to the AC outlet.
Connecting the power cord will turn on the charger
(the pilot lamp lights up).
CAUTION
If the pilot lamp does not light up, pull out the
power cord from the AC outlet and check the
battery mounting condition.
About 1 hour is required to fully charge the battery
at a temperature of about 20°C. The pilot lamp goes
off to indicate that the batterry is fully charged.
(Minutes)
95% of Rated
Voltage
105% of
Rated Voltage
Rated Voltage
(Voltage Listed
on Nameplate)
Charging time
Input Power Supply Voltage
Ambient temperature
Battery: EB12
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi dv 10 dva at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi dv 10 dva in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info