Manual Hitachi DS18DL2 (page 14 of 92) (English, German, Dutch, French, Italian, Portuguese, Spanish)

566530

Zoom out

Zoom in

1/92

English

6. How to select tightening torque and rotational speed

CAUTION:

⅜ The selection examples shown in Table 5 should be

considered as general standard. As different types of

tightening screws and different materials to be

tightened are used in actual works proper adjustments

are naturally necessary.

⅜ When using the driver drill with a machine screw at

HIGH (high speed), a screw may damage or a bit may

loose due to the tightning torque is too strong. Use

the driver drill at LOW (low speed) when using a

machine screw.

NOTE:

The use of the battery in a cold condition (below 0

degree Centigrade) can sometimes result in the

weakened tightening torque and reduced amount of

work. This, however, is a temporary phenomenon,

and returns to normal when the battery warms up.

7. Using the hook

CAUTION:

⅜ When using the hook, pay sufficient attention so that

the main equipment does not fall. If the tool falls,

there is a risk of accident.

⅜ Do not attach the tip tool except phillips bit to the tool

main unit when carrying the tool main unit with the

hook suspended from a waist belt.

Injury may result if you carry the equipment

suspended from the waist belt with sharp tipped

components such as drill bit attached.

The hook can be installed on the right or left side and the

angle can be adjusted in 5 steps between 0° and 80°.

(1) Operating the hook

(a) Pull out the hook toward you in the direction of

arrow (A) and turn in the direction of arrow (B).

(Fig. 10)

(b) The angle can be adjusted in 5 steps (0°, 20°, 40°,

60°, 80°).

Adjust the angle of the hook to the desired position

for use.

(2) Switching the hook position

CAUTION:

Incomplete installation of the hook may result in

bodily injury when used.

(a) Securely hold the main unit and remove the screw

using a slotted head screwdriver or a coin. (Fig. 11)

(b) Remove the hook and spring. (Fig. 12)

securely fasten with screw. (Fig. 13)

NOTE:

Pay attention to the spring orientation. Install the

spring with larger diameter away from you. (Fig. 13)

(3) Using the bit holder (Hook with bit holder)

⅜ Installing the bit

Slide the bit from the side, and then insert firmly

until the groove on the bit locks in the protruded

section of the hook.

⅜ Removing the bit

Securely hold the main unit and pull out the bit by

holding the tip with your thumb. (Fig. 14)

CAUTION:

Only Hitachi STANDARD ACCESSORIES phillips bit

(No. 2 × 65L; Code No. 983006) may be used. Do not

use other bits since they may come loose.

Work Suggestions

Brick <DV14DL2 / DV18DL2>

Wood

Drilling

Steel

Use for drilling purpose.

Aluminum

Machine screw Use the bit or socket matching the screw diameter.

Driving

Wood screw Use after drilling a pilot hole.

Table 4

Use

Clutch dial Position

Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Machine screw 1 – 22

For 6 mm or smaller

diameter screws.

Driving

Wood screw 1 –

For 8 mm or smaller nominal

diameter screws.

For 14 mm or smaller

Brick diameters. (DV14DL2)

For 16 mm or smaller

diameters. (DV18DL2)

Drilling

Wood

For 50 mm or smaller diameters.

(DS14DL2 / DV14DL2)

For 65 mm or smaller diameters.

(DS18DL2 / DV18DL2)

Metal

For 4 mm or smaller

diameter screws.

For 4.8 mm or smaller

nominal diameter screws.

For 10 mm or smaller

diameters. (DV14DL2)

For 12 mm or smaller

diameters. (DV18DL2)

For 24 mm or smaller diameters.

(DS14DL2 / DV14DL2)

For 27 mm or smaller diameters.

(DS18DL2 / DV18DL2)

For drilling with a metal

working drill bit.

Table 5

01Eng_DS14DL2_WE.p65 1/24/12, 10:37 AM13

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi DS18DL2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5,54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi DS18DL2 Manual

Product: