386381

Hitachi ds 9dvf3 Manual

10
Zoom out
Zoom in
Previous page
1/66
Next page
English
9
CAUTION
⅜ The selection examples shown in Table 4 should
be considered as general standard. As different
types of tightening screws and different materials
to be tightened are used in actual works proper
adjustments are naturally necessary.
⅜ When using the driver drill with a machine screw
at HIGH (high speed), a screw may damage or a
bit may loose due to the tightning torque is too
strong. Use the driver drill at LOW (low speed)
when using a machine screw.
6. Mounting and dismounting of the bit
(1) After inserting a driver bit, etc. into the keyless drill
chuck, firmly grasp the ring and tighten the sleeve
by turning it toward the right (in the clockwise
direction as viewed from the front) (See Fig. 9).
⅜ If the sleeve becomes loose during operation, tighten
it further. The tightening force becomes stronger
when the sleeve is tightened additionally.
(2) Dismounting the bit
Firmly grasp the ring and loosen the sleeve by
turning it toward the left (in the counter-clockwise
direction as viewed from the front) (See Fig. 9).
CAUTION
⅜ When it is no longer possible to loosen the sleeve,
use a vise or similar instrument to secure the bit.
Set the clutch mode between 1 and 11, and then
turn the sleeve to the loose side (left side) while
operating the clutch. It should be easy now to
loosen the sleeve.
7. Confirm that the battery is mounted correctly
8. Check the rotational direction
The bit rotates clockwise (viewed from the rear
side) by pushing the R-side of the selector button.
The L-side of the selector button is pushed to turn
the bit counterclockwise (See Fig. 10) (The
L
and
R
marks are provided on the body).
9. Switch operation
⅜ When the trigger switch is depressed, the tool
rotates. When the trigger is released, the tool stops.
⅜ The rotational speed of the drill can be controlled
by varying the amount that the trigger switch is
pulled. Speed is low when the trigger switch is
pulled slightly and increases as the trigger switch
is pulled more.
NOTE
⅜ A buzzing noise is produced when the motor is
about to rotate; This is only a noise, not a machine
failure.
10. Using the hook
CAUTION
⅜ When using the hook, pay sufficient attention so
that the main equipment does not fall. If the tool
falls, there is a risk of accident.
⅜ Do not attach the tip tool except phillips bit to the
tool main unit when carrying the tool main unit with
the hook suspended from a waist belt.
Injury may result if you carry the equipment
suspended from the waist belt with sharp tipped
components such as drill bit attached.
The hook can be installed on the right or left side and
the angle can be adjusted in 5 steps between 0° and
80°.
(1) Operating the hook
(a) Pull out the hook toward you in the direction
of arrow (A) and turn in the direction of arrow
(B) (Fig. 11).
(b) The angle can be adjusted in 5 steps (0°, 20°,
40°, 60°, 80°).
Adjust the angle of the hook to the desired
position for use.
(2) Switching the hook position
CAUTION
Incomplete installation of the hook may result in
bodily injury when used.
(a) Securely hold the main unit and remove the
screw using a slotted head screwdriver or a coin
(Fig. 12).
(b) Remove the hook and spring (Fig. 13).
(c) Install the hook and spring on the other side and
securely fasten with screw (Fig. 14).
NOTE
Pay attention to the spring orientation. Install the
spring with larger diameter away from you (Fig. 14).
(3) Using the bit holder (Hook with bit holder)
⅜ Installing the bit
Slide the bit from the side and then insert firmly
until the groove on the bit locks in the protruded
section of the hook.
5. How to select tightening torque and rotational speed
Use
Clutch Dial
Rotating speed selection (Position of the shift knob)
Position
LOW (Low speed) HIGH (High speed)
Machine screw 1 – 22
For 4 mm or smaller diameter
screws.
Driving
Wood screw 1 –
For 5.8 mm or smaller nominal
diameter screws.
Drilling
Wood
For 25 mm or smaller
diameters. (DS12DVF3)
For 21 mm or smaller
diameters. (DS9DVF3)
Metal
For drilling with a metal
working drill bit.
For 6 mm or smaller
diameter screws.
For 3.8 mm or smaller
nominal diameter screws.
For 12 mm or smaller
diameters.
Table 4
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi ds 9dvf3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi ds 9dvf3 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi ds 9dvf3

Hitachi ds 9dvf3 Additional guide - English - 108 pages

Hitachi ds 9dvf3 User Manual - English - 46 pages

Hitachi ds 9dvf3 Additional guide - German, Dutch - 108 pages

Hitachi ds 9dvf3 User Manual - Danish - 46 pages

Hitachi ds 9dvf3 Additional guide - French, Italian, Portuguese - 108 pages

Hitachi ds 9dvf3 User Manual - Swedish - 46 pages

Hitachi ds 9dvf3 Additional guide - Spanish - 108 pages

Hitachi ds 9dvf3 User Manual - Norwegian, Finnish - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info