Manual Hitachi DS 9 DVF 2 (page 8 of 53) (German, Dutch, French, Italian, Portuguese, Spanish)

79290

Zoom out

Zoom in

1/53

English

CAUTION:

⅜ The selection examples shown in Table 2 should

be utilized as a general standard. As different types

of tightening screws and different materials to be

tightened are used in actual works, proper

adjustments are naturally necessary.

⅜ When using the driver drill with a machine screw

at HIGH (high speed), a screw may damage or a

bit may loose due to the tightning torque is too

strong. Use the driver drill at LOW (low speed)

when using a machine screw.

6. Mounting and dismounting of the bit

(1) After inserting a driver bit, etc. into the keyless drill

chuck, firmly grasp the ring and tighten the sleeve

by turning it toward the right (in the clockwise

direction as viewed from the front). (See Fig. 8)

⅜ If the sleeve becomes loose during operation, tighten

it further. The tightening force becomes stronger

when the sleeve is tightened additionally.

(2) Dismounting the bit

Firmly grasp the ring and loosen the sleeve by

turning it toward the left (in the counter-clockwise

direction as viewed from the front). (See Fig. 8)

CAUTION:

⅜ When it is no longer possible to loosen the sleeve,

use a vise or similar instrument to secure the bit.

Set the clutch mode between 1 and 11, and then

turn the sleeve to the loose side (left side) while

operating the clutch. It should be easy now to

loosen the sleeve.

NOTE:

⅜ There is a plus driver bit on side of the main unit.

The bit can be removed by pulling it forward. After

using the bit, make sure to firmly attach it to the

main body again.

7. Confirm that the battery is mounted correctly

8. Check the rotation direction

The bit rotates clockwise (viewed from the rear

side) by pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn

the bit counter–clockwise. (See Fig. 9) (The

and

marks are provided on the body.)

9. Switch operation

When the trigger switch is pulled, the tool rotates.

When the trigger is released, the tool stops.

⅜ The rotational speed of the drill can be controlled

by varying the amount that the trigger switch is

pulled. Speed is low when the trigger switch is

pulled slightly and increases as the trigger switch

is pulled more.

NOTE:

⅜ A peep sound may be produced when the motor

is about to rotate. This is only a noise, not a machine

failure.

Table 2

Use Cap Position

Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Machine screw 1 – 22

For 4 mm or smaller

diameter screws.

Driving

Wood screw 1 –

For 5.5 mm or smaller

nominal diameter screws.

Drilling

Wood

For 18 mm or smaller

diameters. (DS9DVF2)

For 21 mm or smaller

diameters. (DS12DVF2)

For 25 mm or smaller

diameters. (DS14DVF2)

Metal

For drilling with a metal

working drill bit.

For 6 mm or smaller

diameter screws.

For 3.8 mm or smaller

nominal diameter screws.

For 12 mm or smaller

diameters.

Table 1

Work Suggestions

Wood

Drilling Steel Use for drilling purpose.

Aluminum

Machine screw Use the bit or socket matching the screw diameter.

Driving

Wood screw Use after drilling a pilot hole.

⅜ If the motor is locked, immediately turn the power

off. If the motor is locked for a while, the motor

or battery may be burnt out.

4. The scope and suggestions for uses

The usable scope for various types of work based

on the mechanical structure of this unit is shown

in Table 1.

5. How to select tightening power and rotation speed

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi DS 9 DVF 2 in the language / languages: German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,14 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi DS 9 DVF 2

Hitachi DS 9 DVF 2 User Manual - English, Danish, Swedish, Norwegian, Finnish - 41 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi DS 9 DVF 2 Manual

Product: