78454

Hitachi DS 18 DVF3 Manual

15
Zoom out
Zoom in
Previous page
1/108
Next page
English
15
4. The scope and suggestions for uses
The usable scope for various types of work based on the
mechanical structure of this unit is shown in Table 6.
Table 6
Work Suggestions
Drilling
Wood
Use for drilling purpose.
Steel
Driving
Machine screw Use the bit or socket matching the screw diameter.
Wood screw Use after drilling a pilot hole.
5. How to select tightening torque and rotational speed
Table 7
Use
Clutch Dial
Position
Rotating speed selection (Position of the shift knob)
LOW (Low speed) HIGH (High speed)
Driving
Machine screw 1 – 22
For 4 mm or smaller diameter
screws.
For 6 mm or smaller diameter
screws.
Wood screw
1 –
For 8 mm or smaller nominal
diameter screws. (DS18DVF3)
For 4.8 mm or smaller nominal
diameter screws. (DS18DVF3)
For 6.2 mm or smaller nominal
diameter screws. (DS14DVF3)
For 3.8 mm or smaller nominal
diameter screws. (DS14DVF3/
DS12DVF3/ DS9DVF3)
For 5.8 mm or smaller nominal
diameter screws. (DS12DVF3/
DS9DVF3)
Drilling
Wood
For 38 mm or smaller diameters.
(DS18DVF3)
For 24 mm or smaller diameters.
(DS18DVF3)
For 30 mm or smaller diameters.
(DS14DVF3)
For 12 mm or smaller diameters.
(DS14DVF3/ DS12DVF3/DS9DVF3)
For 25 mm or smaller diameters.
(DS12DVF3)
For 21 mm or smaller diameters.
(DS9DVF3)
Metal
For drilling with a metal working drill
bit.
––––––––––––––––––––––
CAUTION
○ The selection examples shown in Table 7 should be
considered as general standard. As diff erent types of
tightening screws and diff erent materials to be tightened
are used in actual works proper adjustments are naturally
necessary.
○ When using the driver drill with a machine screw at
HIGH
(high speed), a screw may damage or a bit may loose
due to the tightning torque is too strong. Use the driver
drill at LOW (low speed) when using a machine screw.
6. Mounting and dismounting of the bit
<For double sleeve chuck>
(1) After inserting a driver bit, etc. into
the keyless drill chuck,
fi rmly grasp the ring and tighten the sleeve by turning it
toward the right (in the clockwise direction as viewed
from the front) (See Fig. 9).
○ If the sleeve becomes loose during operation, tighten it
further. The tightening force becomes stronger when the
sleeve is
tightened additionally.
(2) Dismounting the bit
Firmly grasp the ring and loosen the sleeve by turning
it toward the left (in the counter-clockwise direction as
viewed from the front) (See Fig. 9).
<For single sleeve chuck>
(1) Mounting the bit
Loosen the sleeve by turning it toward the left (in the
counterclockwise
direction as viewed from the front)
to open the clip on the keyless chuck. After inserting a
driver bit, etc., into the keyless drill chuck, and tighten
the sleeve by turning it toward the right (in the clockwise
direction as viewed from the front) (See Fig. 10).
○ If the
sleeve becomes loose during operation, tighten it
further.
The tightening force becomes stronger when the sleeve
is tightened additionally.
(2) Dismounting the bit
Loosen the sleeve by turning it toward the left (in the
counterclockwise direction as viewed from the front), and
then take out the bit, etc (See Fig. 10).
CAUTION
When it is no longer possible to loosen the sleeve, use a
vise or similar instrument to secure the bit. Set the clutch
mode between 1 and 11, and then turn the sleeve to the
loose side (left side) while operating the clutch. It should
be easy now to loosen
the sleeve.
7. Confi rm that the battery is mounted correctly
000Book_DS9DVF3_WETha.indb 15000Book_DS9DVF3_WETha.indb 15 2012/06/06 8:46:152012/06/06 8:46:15
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi DS 18 DVF3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi DS 18 DVF3 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 7,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi DS 18 DVF3

Hitachi DS 18 DVF3 User Manual - English, Danish, Swedish, Norwegian, Finnish - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info