Manual Hitachi DS 18 DL (page 44 of 50) (English, Danish, Swedish, Norwegian, Finnish)

78872

Zoom out

Zoom in

1/50

English

CAUTION:

⅜ The selection examples shown in Table 5 should be

considered as general standard. As different types of

tightening screws and different materials to be

tightened are used in actual works proper adjustments

are naturally necessary.

⅜ When using the driver drill with a machine screw at

HIGH (high speed), a screw may damage or a bit may

loose due to the tightning torque is too strong. Use

the driver drill at LOW (low speed) when using a

machine screw.

NOTE:

The use of the battery BCL1430, EBL1430, EBM1430

and EBM1830 in a cold condition (below 0 degree

Centigrade) can sometimes result in the weakened

tightening torque and reduced amount of work. This,

however, is a temporary phenomenon, and returns

to normal when the battery warms up.

6. Mounting and dismounting of the bit

(1) Mounting the bit

Loosen the sleeve by turning it toward the left (in the

counterclockwise direction as viewed from the front)

to open the clip on the keyless chuck. After inserting

a driver bit, etc., into the keyless drill chuck, and

tighten the sleeve by turning it toward the right (in

the clockwise direction as viewed from the front).

(See Fig. 9)

⅜ If the sleeve becomes loose during operation, tighten

it further.

The tightening force becomes stronger when the

sleeve is tightened additionally.

(2) Dismounting the bit

Loosen the sleeve by turning it toward the left (in the

counterclockwise direction as viewed from the front),

and then take out the bit ect. (See Fig. 9)

NOTE:

If the sleeve is tightened in a state where the clip of

the keyless chuck is opened to a maximum limit, a

click noise may occur. This is the noise that occurs

when the loosening of the keyless chuck is prevented

and is not a malfunction.

CAUTION:

⅜ When it is no longer possible to loosen the sleeve,

use a vise or similar instrument to secure the bit. Set

the clutch mode between 1 and 7 and then turn the

sleeve to the loose side (left side) while operating the

clutch. It should be easy now to loosen the sleeve.

7. Automatic spindle-lock mechanism

This unit has automatic spindle-lock mechanism for

quick bit changes.

8. Confirm that the battery is mounted correctly

9. Check the rotational direction

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn the

bit counterclockwise. (See Fig. 10) (The

and

marks are provided on the selector button.)

10. Switch operation

⅜ When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

⅜ The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled.

Speed is low when the trigger switch is pulled slightly

and increases as the trigger switch is pulled more.

Use Cap Position

Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Machine screw

1 – 22

For 4 mm or smaller diameter

screws

Driving

Wood screw

1 –

For 8 mm or smaller nominal

diameter screws

For 50 mm or smaller

diameters (DS18DL)

Drilling

Wood

For 45 mm or smaller

diameters (DS14DL)

Metal

For drilling with a metal

working drill bit

For 6 mm or smaller

diameter screws

For 4.8 mm or smaller

nominal diameter screws

For 24 mm or smaller

diameters

Work Suggestions

Wood

Drilling Steel Use for drilling purpose.

Aluminum

Machine screw Use the bit or socket matching the screw diameter.

Driving

Wood screw Use after drilling a pilot hole.

Table 4

4. The scope and suggestions for uses

The usable scope for various types of work based on the mechanical structure of this unit is shown in Table 4.

5. How to select tightening torque and rotational speed

Table 5

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi DS 18 DL in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi DS 18 DL

Hitachi DS 18 DL User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 98 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi DS 18 DL Manual

Product: