Manual Hitachi ds 14 dvf (page 7 of 53) (English, German, Dutch, French, Italian, Portuguese, Spanish)

387453

Zoom out

Zoom in

1/53

English

HOW TO USE

1. Confirm the cap position (See Fig. 4)

The tighthening torque of this unit can be adjusted

according to the cap position, at which the cap is

set.

(1) When using this unit as a screwdriver, line up the

one of the numbers “1, 3, 5 … 22” on the cap, or

the black dots with the triangle mark on the outer

body.

(2) When using this unit as a drill, align the cap drill

mark “

” with the triangle mark on the outer

body.

CAUTION

⅜ The cap cannot be set between the numbers “1,

3, 5 … 22” or the black dots.

⅜ Do not use with the cap set at the black line between

numbers “22” and the drill mark “

”. Doing so

may cause damage. (See Fig. 5)

2. Tlightening torque adjustment

(1) Tightening torque

Tightening torque should correspond in its intensity

to the screw diameter. When too strong torque is

used, the screw head may be broken or be damaged.

Be sure to adjust the cap position accordqFg(Lo the

screw diameter.

(2) Tightening torque indication

The tightening torque differs depending on the type

of screw and the material being tightened.

The unit indicates the tightening torque with the

numbers “1, 3, 5 … 22” on the cap, and the black

dots. The tightening torque at position “1” is the

weakest and the torque is strongest at the highest

number. (see Fig. 4).

(3) Adjusting the tightening torque

Rotate the cap and align the numbers “1, 3, 5 …

22” on the cap, or the black dots with the triangle

mark on the outer body. Adjust the cap in the weak

or the strong torque direction according to the

torque you need.

CAUTION

⅜ The motor rotation may be locked to cease while

the unit is used as a drill. While operating the driver

drill, take care not to lock the motor.

⅜ Too long hammering may cause the screw broken

due to excessive tightening force.

3. Change rotation speed

Operate the shift knob to change the rotation speed.

Move the shift knob in the direction of the arrow

(see Figs. 6 and 7).

When the shift knob is set to “LOW”, the drill

rotates at a low speed. Whe set to “HIGH”, the drill

rotates at a high speed.

CAUTION

⅜ When changing the rotation speed with the shift

knob, confirm that the switch is off.

Changing the speed while the motor is rotating will

damage the gears.

⅜ When setting the shift knob to “HIGH” (high speed)

and the position of the cap is “17” to “22”, it may

happen that the clutch does not engage and that

the motor is locked. In suh a case, please set the

shift knob to “LOW” (low speed).

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latch

(1 pc. or 2 pcs.) to remove the battery (see Figs.

1 and 2).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its direction (see

Fig. 2).

CHARGING

Before using the driver drill, charge the battery as

follows.

1. Insert the battery into the charger.

Insert the battery firmly while observing its direction,

until it contacts the bottom of the charger. (See

Figs. 1 and 3)

CAUTION

The UC9SD, UC12SD and UC14SD models are

the exclusively designed chargers. These cannot

charge batteries except the specified batteries.

It is possible to insert the batteries other than

the specified into the chargers and some of

them may light up the pilot lamps. However,

you are requested to exercise utmost caution

not to charge batteries other than specified ones

because these can not only be charged but also

such actions can result in the malfuntion of

chargers.

2. Connect the charger power cord to the receptacle.

Connecting the power cord will turn on the charger

(the pilot lamp lights up).

CAUTION

If the pilot lamp does not light up, pull out the

power cord from the receptacle and check the

battery mounting condition.

About 1 hour is required to fully charge the battery

at a temperature of about 20°C. The pilot lamp goes

off to indicate that the battery is fully charged.

The battery charging time becomes longer when a

temperature is low or the voltage of the power

source is too low.

When the pilot lamp does not go off even if more

than two hours have elapsed after starting of the

charging, stop the charging and contact your

HITACHI AUTHORIZED SERVICE CENTER.

CAUTION

If the battery is heated due to direct sunlight,

etc., just after operation, the charger pilot lamp

may not light up. At that time, cool the battery

first, then start charging.

3. Disconnect the charger power cord from the

receptacle.

4. Hold the charger tight and pull out the battery.

PRIOR TO OPERATION

1. Setting up and checking the work environment

Check if the work environment is suitable by follow-

ing the precautions.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi ds 14 dvf in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi ds 14 dvf Manual

Product: