Manual Hitachi ds 14 dsl (page 14 of 82) (English, German, Dutch, French, Italian, Portuguese, Spanish)

389002

Zoom out

Zoom in

1/82

English

As the remaining battery indicator shows somewhat

differently depending on ambient temperature and

battery characteristics, read it as a reference.

NOTE:

⅜ Do not give a strong shock to the switch panel or

break it.It may lead to a trouble.

⅜ To save the battery power consumption, the

remaining battery indicator lamp lights while pressing

the remaining battery indicator switch.

8. How to use the LED light

Every time you press the light switch on the switch

panel, the LED light lights or goes off. (Fig. 12)

To prevent the battery power consumption, turn off

the LED light frequently.

CAUTION:

⅜ Do not expose directly your eye to the light by looking

into the light.

If your eye is continuously exposed to the light, your

eye will be hurt.

NOTE:

⅜ To prevent the battery power consumption caused

by forgetting to turn off the LED light, the light goes

off automatically in about 15 minutes.

9. Mounting and dismounting of the bit

(1) Mounting the bit

Loosen the sleeve by turning it toward the left (in the

counterclockwise direction as viewed from the front)

to open the clip on the keyless chuck. After inserting

a driver bit, etc., into the keyless drill chuck, and

tighten the sleeve by turning it toward the right (in

the clockwise direction as viewed from the front).

(See Fig. 13)

⅜ If the sleeve becomes loose during operation, tighten

it further.

The tightening force becomes stronger when the

sleeve is tightened additionally.

(2) Dismounting the bit

Loosen the sleeve by turning it toward the left (in the

counterclockwise direction as viewed from the front),

and then take out the bit ect. (See Fig. 13)

NOTE:

If the sleeve is tightened in a state where the clip of

the keyless chuck is opened to a maximum limit, a

click noise may occur. This is the noise that occurs

when the loosening of the keyless chuck is prevented

and is not a malfunction.

CAUTION:

⅜ When it is no longer possible to loosen the sleeve,

use a vise or similar instrument to secure the bit. Set

the clutch mode between 1 and 11 and then turn the

sleeve to the loose side (left side) while operating the

clutch. It should be easy now to loosen the sleeve.

10. Automatic spindle-lock mechanism

This unit has automatic spindle-lock mechanism for

quick bit changes.

11. Confirm that the battery is mounted correctly

12. Check the rotational direction

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn the

bit counterclockwise. (See Fig. 14) (The

and

marks are provided on the selector button.)

13. Switch operation

⅜ When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

⅜ The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled.

Speed is low when the trigger switch is pulled slightly

and increases as the trigger switch is pulled more.

NOTE:

⅜ A buzzing noise is produced when the motor is about

to rotate; This is only a noise, not a machine failure.

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade efficiency and

cause possible motor malfunction, sharpen or replace

the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes (Fig. 15)

The motor employs carbon brushes which are

consumable parts. Since and excessively worn carbon

brush can result in motor trouble, replace the carbon

brush with new ones when it becomes worn to or

near the “wear limit”. In addition, always keep carbon

brushes clean and ensure that they slide freely whthin

the brush holders.

NOTE:

When replacing the carbon brush with a new one, be

sure to use the Hitachi Carbon Brush Code No. 999054.

5. Replacing carbon brushes

Take out the carbon brush by first removing the

brush cap and then hooking the protrusion of the

carbon brush with a flat head screw driver, etc., as

shown in Fig. 17.

When installing the carbon brush, choose the direction

so that the nail of the carbon brush agrees with the

contact portion outside the brush tube. Then push it

in with a finger as illustrated in Fig. 18. Lastly, install

the brush cap.

State of lamp Battery Remaining Power

The battery remaining power

is enough.

The battery remaining power

is a half.

The battery remaining power

is nearly empty.

Re-charge the battery soonest

possible.

Table 6

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi ds 14 dsl in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi ds 14 dsl

Hitachi ds 14 dsl Additional guide - English, German, Dutch, French, Italian, Portuguese, Spanish - 84 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi ds 14 dsl Manual

Product: