Manual Hitachi DS 12 DM (page 11 of 70) (English, German, Dutch, French, Italian, Portuguese, Spanish)

78450

Zoom out

Zoom in

1/70

English

CAUTIONS:

⅜ The selection examples shown in Table 5 should

be considered as general standard. As different

types of tightening screws and different materials

to be tightened are used in actual works proper

adjustments are naturally necessary.

⅜ When using the driver drill with a machine screw

at HIGH (high speed), a screw may damage or a

bit may loose due to the tightning torque is too

strong. Use the driver drill at LOW (low speed)

when using a machine screw.

NOTE:

The use of the battery EB1222HL and EB1230HL in

a cold condition (below 0 degree Centigrade) can

sometimes result in the weakened tightening torque

and reduced amount of work. This, however, is

a temporary phenomenon, and returns to normal

when the battery warms up.

6. Using the hook

The hook can be installed on the right or left side

and the angle can be adjusted in 5 steps between

0° and 80°.

(1) Operating the hook

(a) Pull out the hook toward you in the direction

of arrow (A) and turn in the direction of arrow

(B). (Fig. 8)

(b) The angle can be adjusted in 5 steps (0°, 20°,

40°, 60°, 80°).

Adjust the angle of the hook to the desired

position for use.

(2) Switching the hook position

CAUTION:

Incomplete installation of the hook may result in

bodily injury when used.

(a) Securely hold the main unit and remove the

screw using a slotted head screwdriver or a

coin. (Fig. 9)

(b) Remove the hook and spring. (Fig. 10)

securely fasten with screw. (Fig. 11)

NOTE:

Pay attention to the spring orientation. Install the

spring with larger diameter away from you. (Fig.

11)

(3) Using the bit holder

⅜ Installing the bit

Slide the bit from the side in the direction of

Fig. 12, and then insert firmly until the groove

on the bit locks in the protruded section of the

hook.

⅜ Removing the bit

Securely hold the main unit and pull out the bit

by holding the tip with your thumb. (Fig. 13)

CAUTIONS:

⅜ The bit may come loose from the hook and cause

bodily injury when reversing the direction of the

bit as shown in Fig. 12 or when using the driver

with the bit stored incomplete.

⅜ Only Hitachi OPTIONAL ACCESSORIES plus driver

bits (Bit No. 2; Code No. 992671, Bit No. 3; Code

No. 992672) may be used. Do not use other bits

since they may come loose.

7. Mounting and dismounting of the bit

(1) Mounting the bit

Loosen the sleeve by turning it toward the left (in

the counterclockwise direction as viewed from the

front) to open the clip on the keyless chuck. After

inserting a driver bit, etc., into the keyless drill

chuck, and tighten the sleeve by turning it toward

the right (in the clockwise direction as viewed from

the front). (See Fig. 14)

⅜ If the sleeve becomes loose during operation, tighten

it further.

The tightening force becomes stronger when the

sleeve is tightened additionally.

(2) Dismounting the bit

Loosen the sleeve by turning it toward the left (in

the counterclockwise direction as viewed from the

front), and then take out the bit ect. (See Fig. 14)

NOTE:

If the sleeve is tightened in a state where the clip

of the keyless chuck is opened to a maximum limit,

a click noise may occur. This is the noise that occurs

when the loosening of the keyless chuck is prevented

and is not a malfunction.

CAUTION:

⅜ When it is no longer possible to loosen the sleeve,

use a vise or similar instrument to secure the bit.

Set the clutch mode between 1 and 11 and then

turn the sleeve to the loose side (left side) while

operating the clutch. It should be easy now to

loosen the sleeve.

8. Automatic spindle-lock mechanism

This unit has automatic spindle-lock mechanism for

quick bit changes.

For 6 mm or smaller

diameter screws.

For 3.8 mm or smaller

nominal diameter screws.

For 18 mm or smaller

diameters.

5. How to select tightening torque and rotational speed

Table 5

Use Clutch Position

Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Driving

Machine screw 1 – 22

For 4 mm or smaller diameter

screws.

Wood screw 1 –

For 6.8 mm or smaller nominal

diameter screws.

Drilling

Wood

For 27 mm or smaller

diameters.

Metal

For drilling with a metal

working drill bit.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi DS 12 DM in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi DS 12 DM

Hitachi DS 12 DM User Manual - English, Danish, Swedish, Norwegian, Finnish - 38 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi DS 12 DM Manual

Product: