566509
8
Zoom out
Zoom in
Previous page
1/56
Next page
English
7
SPECIFICATIONS
*
Be sure to check the nameplate on product as it is subject to change by areas.
Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)
Power input 950 W*
Capacity Drill bit: 38 mm
Core bit: 105 mm
No load speed 620 min
–1
Full-load impact rate 2800 min
–1
Weight (without cord, side handle) 6.4 kg
(1) Drill bit (taper shank)
External dia.: 11, 12, 14.3,
14.5, 17.5,
21.5 mm
(2) Taper shank
adapter
(3) Cotter
STANDARD ACCESSORIES
(1) Case (Molded plastic) ................................................. 1
(2) Side Handle ................................................................. 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
Through-hole drilling (Rotation + Hammering)
(1) Drill bit (hexagon shank)
Overall length: 280, 400, 505 mm
External dia.: 16, 19, 22, 25, 28, 32, 38 mm
Anchor hole drilling (Rotation + Hammering)
ROTARY HAMMER SAFETY WARNINGS
1. Wear ear protectors
Exposure to noise can cause hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Do not touch the bit during or immediately after
operation. The bit becomes very hot during
operation and could cause serious burns.
4. Before starting to break, chip or drill into a wall,
floor or ceiling, thoroughly confirm that such items
as electric cables or conduits are not buried inside.
5. Always hold the body handle and side handle of
the power tool firmly. Otherwise the counterforce
produced may result in inaccurate and even
dangerous operation.
6. Wear a dust mask
Do not inhale the harmful dusts generated in
drilling or chiseling operation. The dust can
endanger the health of yourself and bystanders.
Taper shank
adapter
Morse taper
(No. 1)
Morse taper
(No. 2)
A-taper
B-taper
Application drill bit
Drill bit (taper shank)
11, 12, 14.3, 14.5, 17.5 mm
Drill bit (tape shank)
21.5 mm
Taper shank adapter formed A-
taper or B-taper is provided as
optional accessory, but drill bit for
it is not provided.
(2) Core
bit
(3) Core bit
shank
(Guide
plate)
(1) Center
pin
Large dia. hole boring (Rotation + Hammering)
(1) Center pin
Applied to core bits from 38 mm to 105 mm
Applied to core bits 32 mm and 35 mm
NOTE
Do not use core bits 25 mm or 29 mm.
(2) Core bit
External dia. 25, 29, 32, 35, 38, 45, 54, 64, 79, 94,
105 mm
(with guide plate, not applicable to cores 25 mm or
29 mm)
(3) Core bit shank
Applied to core bits above 38 mm
Applied to core bits below 35 mm
Anchor work (for self-anchors)
01Eng_DH38SS_WE 4/27/09, 17:007
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi DH38SS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi DH38SS in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info