661490
7
Zoom out
Zoom in
Previous page
1/196
Next page
7
English
MOUNTING AND OPERATION
Action Figure Page
Removing and inserting the
battery
1 185
Charging 2 185
Remaining battery indicator 3 185
Installing / Removing the side
handle
4 185
Inserting SDS-plus drilling tools 5 186
Removing SDS-plus drilling tools 6 186
Selecting rotation direction 7 186
Selecting the operating mode 8 186
Adjusting the drilling depth 9 186
Changing the chisel position 10 186
Removing drill bit holder
(DH36DBQL, DH36DBML)
*1
11 187
Inserting drill chuck holder
(DH36DBQL, DH36DBML)
12 187
Inserting round shank applications
tools (DH36DBQL, DH36DBML)
13 187
Switch operation 14 187
How to use the LED light 15 187
Cleaning of the battery installation
compartment
16 187
Selecting accessories
188, 189
*1 If it is hard to pull out the drill chuck holder or the drill bit
holder, align the change lever with the
mark and turn
the lock grip.
For details on how to use the dust extraction unit, refer to
the separate instruction manual included with this tool.
(DH36DBDL/DH36DBML)
REACTIVE FORCE CONTROL
This product is equipped with a Reactive Force Control
(RFC) feature that reduces jerking of the tool body.
If the tool bit is suddenly overburdened, any jerking of the
tool body is reduced by activation of the slip clutch or by
stopping of the motor by the sensor built into the tool body.
If the motor is stopped because of overburdening detection
by the controller, this is indicated by blinking of the remaining
battery lamp while the switch is pulled. (Fig. 17)
Because the RFC feature may not activate or its performance
may be insu cient depending on the working environment
and conditions, be careful not to suddenly overburden the
tool bit while operating.
Possible causes of sudden overburdening
1 Tool bit biting into material
2 Impact against nails, metal or other hard objects
3 Tasks involving prying or any excess application of
pressure, etc.
Also, other causes include any combination of the
aforementioned.
When the reactive force control (RFC) is triggered
When the RFC is triggered and the motor stops, turn
o the tool’s switch and remove the cause of the
overburdening before continuing operation.
Fig. 17
LUBRICATION
Low viscosity grease is applied to this rotary hammer so
that it can be used for a long period without replacing the
grease. Please contact the nearest service center for grease
replacement when any grease is leaking form loosened
screw.
Further use of the rotary hammer despite the grease
shortage causes damage to reduce the service life.
CAUTION
A speci c grease is used with this machine, therefore,
the normal performance of the machine may be badly
a ected by use of di erent grease. Please be sure to let
one of our service centers to undertake replacement of
the grease.
MAINTENANCE AND INSPECTION
CAUTION
Be sure to turned o the switch and remove the battery
before maintenance and inspection.
1. Inspecting the tool
Since use of as dull tool will degrade e ciency and
cause possible motor malfunction, sharpen or replace
the tool as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Cleaning on the outside
When the power tool is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use chloric
solvents, gasoline or paint thinner, for they melt plastics.
5. Cleaning of the battery installation compartment
After drilling concrete, if concrete dust has accumulated
on the terminals or the area where the battery slides
within the battery installation compartment, clean o the
accumulated concrete dust with a dry cloth before using
the tool. (Fig. 16)
Also, after cleaning, ensure that the battery can be
installed and removed smoothly from the tool.
CAUTION
Using the tool when the battery is covered with concrete
dust may lead to accidents such as the battery falling
during use.
Furthermore, such use may cause a malfunction or
contact failure between the battery and the terminals.
6. Storage
Store the power tool in a place in which the temperature
is less than 40°C and out of reach of children.
0000Book_DH36DBL.indb 70000Book_DH36DBL.indb 7 2017/03/29 17:03:392017/03/29 17:03:39
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi DH36DBML at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi DH36DBML in the language / languages: All languages as an attachment in your email.

The manual is 19,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info