Manual Hitachi D13VB2-2 (page 6 of 26) (English, German, Dutch, French, Italian, Portuguese, Spanish)

566262

Zoom out

Zoom in

1/26

English

SPECIFICATIONS

Model D13VB2 D13T2

Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)

Power input 750W*

Speed change 1 2 1 2

No load speed 0–1100/min 0–2600/min 1100/min 2600/min

Capacity

Steel 13 mm 8 mm 13 mm 8 mm

Wood 40 mm 25 mm 40 mm 25 mm

Weight (without cord)

Spec. for chuck fitted with chuck wrench 2.1 kg

Spec. for keyless chuck 2.3 kg

*Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Chuck Wrench (Spec. only for chuck fitted with

chuck wrench) ........................................................... 1

(2) Side Handle ............................................................... 1

(3) Depth Gauge ............................................................. 1

Standard accessories are subject to change without no-

tice.

OPTIONAL ACCESSORIES (sold separately)

⅜ Drill Stand (Model D10–DS)

Optional accessories are subject to change without no-

tice.

APPLICATIONS

⅜ Boring holes in metal, wood and plastic.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized con-

forms to the power requirements specified on the

product nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, inviting serious

accident.

3. Extension cord

When the work area is removed from the power

source. Use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Mounting and dismounting of the bit.

For Drill chuck with chuck wrench (Fig. 1)

Fit the drill bit into the chuck and use the chuck

wrench to secure it, tightening the chuck by each

of the three holes in turn.

For keyless chuck (Fig. 2, 3)

(1) Mounting the bit

Turn the lock collar in the direction “AUF” and open

the chuck. After Inserting the drill bit Into the chuck

as far it will go, turn the lock collar in the “ZU”

direction. Grip the retaining ring and close the chuck

by turning the sleeve clockwise as viewed from the

front.

(2) Dismounting the bit

Turn the lock collar in the direction “AUF” to release

the shucking force. Grip the retaining ring and open

the chuck by turning the sleeve counterclockwise.

NOTE

When the sleeve does not become loose any fur-

ther, fix the side handle to retaining ring, hold side

handle firmly, then turn the sleeve to loosen by

hand. (Fig. 4)

5. Selecting the appropriate drill bit

⅜ When boring metal or plastic

Use an ordinary metalworking drill bit.

⅜ When boring wood

Use an ordinary woodworking drill bit.

However, when drilling 6.5 mm or smaller holes,

use a metalworking drill bit.

6. Confirm the direction of bit rotation (Fig. 5)

The bit rotates clockwise (viewed from the rear

side) by pushing the R-side of the reversing switch

lever. The L-side of the lever is pushed to turn the

bit counterclockwise. (for D13VB2 only)

7. Fixing the side handle (Fig. 6)

Loosen the wing bolt on the side handle, and attach

the side handle to the gear cover in a position

convenient for drilling. Match the projecting part of

the handle to the groove on the gear cover, and

firmly tighten the wing bolt. To remove the side

handle, loosen the wing bolt and rotate the handle.

To attach a depth gauge on the side handle, insert

the gauge into the U-shaped groove on the side

handle, adjust the position of the depth gauge in

accordance with the desired depth of the hole, and

firmly tighten the wing bolt.

8. High-spped/Low-speed changeover

To change speed, rotate the gear shift dial as

indicated by the arrow in Fig. 7. The numeral “1”

engraved on the drill body denotes low speed, the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi D13VB2-2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi D13VB2-2 Manual

Product: