566259

Hitachi D10YB2 Manual

6
Zoom out
Zoom in
Previous page
1/30
Next page
4
English
PRECAUTIONS ON USING ANGLE DRILL
1. Wear ear protectors with impact drills.
Exposure to noise can cause hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Hold the drill and side handle securely with both
hands when using.
4. Do not wear gloves made of stuff liable to roll
up such as cotton, wool, cloth or string, etc.
5. Prior to drilling into walls, ceilings or floors, ensure
there are no electric cables or conduits inside.
STANDARD ACCESSORIES
(1) Chuck wrench ............................................................ 1
(2) Side handle ................................................................ 1
Standard accessories are subject to change without
notice.
APPLICATIONS
⅜ Drilling holes on various metal, wood and plastics.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, inviting serious
accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Confirm the direction of bit rotation (Fig. 1)
The bit rotates clockwise (viewed from the top side)
by pushing the R-side of the reversing switch lever.
The L-side of the lever is pushed to turn the bit
counterclockwise.
CAUTION
Never change the direction of bit rotation while
operating.
SPECIFICATIONS
Voltage (by areas)* (110V, 115V, 220V, 230V, 240V)
Power input* 500 W
No-load speed 500 – 2300 min
–1
Drill chuck capacity 10 mm
Capacity: Steel 10 mm
Wood 22 mm
Weight (without cord) 1.5 kg
*Be sure to check the nameplate on product as it is subject to change by areas.
Turn the power switch OFF before changing the
direction of bit rotation; otherwise, burning of the
motor will result.
5. Mounting drill bits (Fig. 2)
Tighten drill bits with the chuck wrench. There are
three holes in which the chuck wrench should be
inserted. Tighten them equally in turn at three holes,
without tightening them only at one hole. The drill
bit can be removed in the opposite method as
mentioned above.
6. How to select drill bits
(1) When drilling holes in metals or plastics:
Use ordinary metalworking drill bits, applicable drill
sizes range from min. 1.5 mm to drill chuck capacity.
(2) When drilling holes in wood:
Use woodworking drill bits. For small holes of 6.5
mm diam. or below, use metalworking drill bits.
7. Fixing the side handle
Screw the side handle into the gear cover.
HOW TO USE
1. Switching instruction
(1) Turning the switch on
Slide the switch lever on the main body backward
as illustrated in Fig. 3. When you slide it backward
completely, the switch gets turned on and locked
in that condition.
(2) Turning the switch off
Press the round convex on the surface of the switch
lever as illustrated in Fig. 4. Then, the lock comes
off, the switch lever returns forward on the main
body by the spring’s force, and the switch gets
turned off.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi D10YB2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi D10YB2 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info