Manual Hitachi D10VSTL (page 7 of 40) (English, German, Dutch, French, Italian, Portuguese, Spanish)

566255

Zoom out

Zoom in

1/40

English

DRILL SAFETY WARNINGS

1. Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

2. Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord. Cutting accessory contacting a "live" wire may

make exposed metal parts of the power tool "live"

and could give the operator an electric shock.

3. Hold the drill securely when using.

4. Do not wear gloves made of stuff liable to roll up

such as cotton, wool, cloth or string, etc.

5. Prior to drilling into walls, ceilings or floors, ensure

there are no electric cables or conduits inside.

6. Do not use the tool for tightening or loosening of

screws, bolts, etc.

Doing so may cause damage to the tool or personal

injury.

STANDARD ACCESSORIES

⅜ Chuck wrench (Spec. only for keyed chuck) ..... 1

Standard accessories are subject to change without notice..

APPLICATIONS

⅜ Boring holes in metal, wood and plastic.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, inviting serious

accident.

3. Extension cord

When the work area is removed from the power

source. Use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Selecting the appropriate drill bit:

⅜ When boring metal or plastic

Use ordinary metalworking drill bits.

⅜ When boring wood

Use ordinary woodworking drill bits.

However, when drilling 6.5 mm or smaller holes,

use a metalworking drill bit.

5. Mounting and dismounting of the bit

For keyed chuck (Fig. 1)

(1) Open the chuck jaws, and insert the bit into the

chuck.

(2) Place the chuck wrench in each of the three holes

in the chuck, and turn it in the clockwise direction

(viewed from the front side). Tighten securely.

(3) To remove the bit, place the chuck wrench into one

of the holes in the chuck and turn it in the

counterclockwise direction.

For keyless chuck (Fig. 2)

(1) Open the chuck jaws, and insert the bit into the

chuck.

To open the chuck jaws, hold the ring while turning

the sleeve in the counterclockwise direction (viewed

from the front side).

(2) Firmly grasp the ring and turn the sleeve in the

clockwise direction. Tighten securely.

(3) To remove the bit, firmly grasp the ring and turn

the sleeve in the counterclockwise direction.

(4) If it is hard to loosen the sleeve, fix the spindle

using the open-end wrench, hold the sleeve firmly,

and turn it in the loosening direction

(counterclockwise when viewed from the front).

(Fig. 3)

6. Check the rotational direction (Fig. 4)

The bit rotates clockwise (viewed from the rear

side) by turning the rotational change lever to R-

mark.

The rotational change lever is returned to the L-

mark to turn the bit counterclockwise.

(The

and

marks are provided on the body.)

7. RCD

The use of a residual current device with a rated

residual current of 30mA or less at all times is

recommended.

SPECIFICATIONS

Voltage (by areas)* (110 V, 220 V, 230 V, 240 V)

Power input 450 W*

No load speed 0 – 3200 min

–1

Drill chuck capacity 10 mm

Capacity

Steel 10 mm

Wood 25 mm

Weight (without cord) 1.2 kg

*Be sure to check the nameplate on product as it is subject to change by areas.

01Eng_D10VST_WE 2/1/12, 13:156

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi D10VSTL in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi D10VSTL Manual

Product: