Manual Hitachi CS33EDT (page 10 of 80) (English, German, Dutch, French, Italian, Portuguese, Spanish)

566210

Zoom out

Zoom in

1/80

English

SPECIFICATIONS

○ Code CS of model name means Chain saw

Model CS33EDT (30) CS33EDT (35)

Typ e of equipment Chain saw, portable

Engine Size (cm

) 32.2

Spark Plug NGK BPMR-7A

Fuel Tan k Capacity (cm

)290

Chain Oil Ta nk Capacity (cm

)180

Dry Weight (kg)

(Without guide bar and chain)

3.4

Guide bar length (mm) 300 350

Chain pitch (mm) 9.53

Chain gauge (mm) 1.27

Sound pressure level LpA (dB (A)) by ISO 22868

Equivalent

Uncertainty

100

Sound power level LwA (dB (A)) by ISO 22868

Measured

Uncertainty

Sound power level LwA (dB (A)) by 2000/14/EC

Measured

Guaranteed

109

113

116

Vibration level (m/s

) by ISO 22867

Front handle

Rear handle

Uncertainty

4.4

6.1

0.8

Max. engine power by ISO 7293 (kW) 1.3/9300

Max. engine speed (min

-1

) 12000

Idle engine speed (min

-1

) 3000

Speciﬁ c fuel consumption (g/kWh) 567

Typ e of chain

91VG045

(Oregon)

91VG052

(Oregon)

Max. chain speed (m/sec) 22.9

Sprocket (number of teeth) 6

NOTE: Equivalent noise level/vibration levels by ISO 22868/22867 are calculated as the time-weighted energy total for noise/vibration levels

under various working conditions with the following time distribution: 1/3 idle, 1/3 full, 1/3 racing speed.

*All

data subject to change without notice.

ASSEMBLY PROCEDURES

WARNING

Never try to start engine without side case, bar and chain

securely fastened.

1. Pull the chain brake (18) toward the front handle to check that the

brake is disengaged. (Fig. 15).

2. Remove guide bar clamp nut (2). Remove the side case (3)

(Fig. 2)

* In

case of installing the spiked bumper (4), install the spiked

bumper (4) to the unit with two screws. (Fig. 3)

3. Install the guide bar (5) onto the bolts (6), then push it toward the

sprocket (7) as far as it will go. (Fig. 4)

4. Conﬁ rm the

direction of saw chain (10) is correct as in the ﬁ gure,

and align the chain on the sprocket. (Fig. 5)

5. Guide the chain drive links into the bar groove all around the bar.

6. Install the side case (3) onto the bolts (6).

Make sure that the boss of chain

tension adjust bolt (8) ﬁ ts into

the hole of the bar (9). (Fig. 4)

Then tighten the guide bar clamp nut (2) by hand that allows the

chain bar end to move up and down easily.

(

Fig. 2

)

7. Raise the bar end, and tighten the saw chain (10) by turning the

tension adjustment bolt (11) clockwise. To check proper tension,

lightly lift up the center of chain and there should be about 0.5 – 1.0

mm clearance between bar and edge of drive link (12). (Fig. 6,

CAUTION

PROPER TENSION IS EXTREMELY IMPORTANT

8. Raise the bar end, and securely tighten the guide bar clamp nut

with the combi box spanner. (Fig. 7)

9. A new chain will stretch so adjust the chain after a few cuts and

watch chain tension carefully for the ﬁ rst half hour

of cutting.

NOTE

Check the chain tension frequently for optimum performance

and durability.

CAUTION

○ When the chain is excessively tightened, the bar and chain will

be damaged rapidly. Conversely, when the chain is excessively

loosened, it may get out of the groove in the bar.

○ Always wear gloves when touching the

chain.

WARNING

During operation, hold chain saw ﬁ rmly with both hands. A single

hand operation may cause serious injury.

000Book_CS33EDT_WE.indb 9000Book_CS33EDT_WE.indb 9 2011/08/06 9:14:552011/08/06 9:14:55

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CS33EDT in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 15,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi CS33EDT Manual

Product: