565940

Hitachi CM9UBY Manual

8
Zoom out
Zoom in
Previous page
1/56
Next page
7
English
SPECIFICATIONS
Model CM9SR CM9UBY
Voltage (by areas)*
1
(110V, 230V)
Power input*
1
2000W 2600W
No-load speed 6600 min
–1
Dimensions of diamond wheel
Max. cutting depth 60mm
Weight (without cord and diamond wheel) 7.7kg 8.1kg
Starting current limiter*
2
No Yes
*1 Be sure to check the nameplate on product as it is subject to change by areas.
*2 The starting current limiter produces the starting current to such an extent that a fuse (16 A, slow-blow)
is not tripped.
Outer dia. 230mm
Thickness 2.5mm
Hole dia. 22.2mm
Kickback will propel the tool in direction opposite to
the wheel’s movement at the point of snagging.
d) Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the wheel.
Corners, sharp edges or bouncing have a tendency
to snag the rotating wheel and cause loss of control
or kickback.
e) Do not attach a saw chain woodcarving blade or
toothed saw blade.
Such blades create frequent kickback and loss of
control.
f) Do not “jam” the wheel or apply excessive pressure.
Do not attempt to make an excessive depth of cut.
Overstressing the wheel increases the loading and
susceptibility to twisting or blinding of the wheel in
the cut and the possibility of kickback or wheel
breakage.
g) When wheel is binding or when interrupting a cut
for any reason, switch off the power tool and hold
the power tool motionless until the wheel comes to
a complete stop. Never attempt to remove the wheel
from the cut while the wheel is in motion otherwise
kickback may occur.
Investigate and take corrective action to eliminate
the cause of wheel binding.
h) Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter
the cut.
The wheel may bind, walk up or kickback if the power
tool is restarted in the workpiece.
i) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near
the line of cut and near the edge of the workpiece on
both sides of the wheel.
j) Use extra caution when making a “pocket cut” into
existing walls or other blind areas.
The protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kickback.
PRECAUTION ON USING CUTTER
1. Never attach any tool except the diamond wheel as
specified by the manufacturer.
Do not operate the cutter while applying water.
2. Always check the diamond wheel before starting the
machine. If it is cracked, broken or bent, do not use
it. Carefully start the machine to check for other
abnormalities.
3. Using the diamond wheel to cut metal will shorten
its service life or will result in breakage. Never use
the diamond wheel to cut metal.
4. Start working only when maximum rotation speed
is reached.
5. Excessive force overloads the motor and reduces
working efficiency and service life. Always cut
concrete, tile or stone with a cutting depth of 50mm
or less. If the cutting depth is more than 50mm,
cut the workpiece 2 or 3 times. If the workpiece is
cut with a cutting depth of more than 50mm, the
service life of the diamond wheel will be reduced
and the motor may seize.
6. Do not use this machine to cut asbestos.
7. In operations using a cutting wheel, if flame comes
out, cover the dust collection adaptor with a rubber
cap and be sure to wear protective glasses.
STANDARD ACCESSORIES
(1) Wrench ........................................................................ 1
(2) Adaptor ....................................................................... 1
Standard accessories are subject to change without notice.
APPLICATION
⅜ Cutting or scribing concrete
⅜ Cutting or scribing tile
⅜ Cutting or scribing stone
⅜ Cutting or scribing roof tile
01Eng_CM9SR_WE 6/30/08, 18:167
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CM9UBY at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CM9UBY in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info