565926

Hitachi CM14E Manual

22
Zoom out
Zoom in
Previous page
1/232
Next page
22
GB
Every unit is run at the factory and the carburettor
is set in compliance with Emission Regulations.
In addition, the carburettor is equipped with “H”
(High Speed Needle) and “L” (Low Speed Needle)
needle adjustment limiters that prevent settings
outside acceptable limits.
1. Before adjusting carburettor clean or replace air
fi lter and muffl er.
2. Start engine and run several minutes to bring to
operating temperature. Flash choke twice during
warm-up to clear any air from the fuel system.
3. Stop engine.
Turn “H” speed needle anticlockwise to stop.
Turn “L” speed needle midway between full
clockwise stop and anticlockwise stop.
4. Idle Speed Adjustment:
• Start engine, turn “Idle” speed adjustment knob
clockwise until the wheel begins to turn, then
turn knob out anticlockwise until the wheel
stops turning. Turn knob out, anticlockwise, an
additional 1/4 turn.
WARNING
Cutting attachment must not turn or move
when unit is idling.
5. Accelerate to full throttle for 2 - 3 seconds to
clear any excess fuel in the engine, then return
to idle.
Accelerate engine to full throttle to check for
smooth transition from idle to high speed.
If engine hesitates turn “L” needle anticlockwise
1/8 turn and repeat acceleration. Continue
adjustment until smooth acceleration results.
6. Check idle speed and reset if necessary as
described in item 4. If a tachometer is available
idle speed should be set as specifi ed in the
Operator’s Manual.
CAUTION
When starting, idling adjustment speed
should be adjusted not to rotate the wheel.
Correct idle speed is adjusted 2600 to 2800 r/
min. Or 1/4 turn anticlockwise from the point
the wheel stops moving.
When there is some trouble with the
carburettor, refer to your distributor or
dealer.
Idle speed
adjustment knob
H: High speed needle
L: Low speed needle
Carburettor Adjustment
CM14E_WE_all.indb 22CM14E_WE_all.indb 22 2008/02/05 21:09:332008/02/05 21:09:33
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CM14E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CM14E in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 9,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info