Manual Hitachi CM14E (page 19 of 232) (English, German, Dutch, French, Italian, Portuguese, Spanish)

565926

Zoom out

Zoom in

1/232

Maintenance and Adjustment

Rib Ace-belt Change and Adjustment

1. Move ignition switch down “STOP” position.

2. Remove belt tension (with 13 mm end of the box

wrench) by turning the cam anticlockwise.

3. Remove rear arm cover and front arm cover.

(Save the seven screws.)

4. Use the 13 mm end of the box wrench to loosen

arm mounting nuts just a little.

5. Push arm towards small pulley. Pull belt off

pulley at point (B) and slip new belt onto small

pulley. At point (A), start belt over the rim and

onto the large pulley.

6. Reinstall the covers. Turn the tension adjusting

cam clockwise until the edge of the arrow in the

peep window reachs the line. (See drawing.)

7. Lightly swing the tip of the arm up and

down several times. This sets the tension

automatically.

8. Tighten the arm mounting nuts fully.

Remounting Arm for Flush Cutting

When necessary to cut up close to a barrier, invert and remount the arm so

the wheel is on the outboard side.

1. Refer to “Rib Ace-belt Change and Adjustment” to remove the belt. This

time, remove the arm mounting nuts, the long plate.

2. Use the parts removed in step one to remount the arm – this time in the

inverted position. (This time, direction of wheel rotation is opposite to the

arrow.)

3. Push the wheel shield and arm through loop of the Rib Ace-belt. Follow

instructions to mount and tension the Rib Ace-belt.

4. Reinstall all parts previously removed, and tension the belt.

Rear Arm Cover Front Arm Cover

Arm Mounting Nuts

Cam

Small

Pulley (A)

Large Pulley (B)

Small

Pulley (A)

Large Pulley (B)

Rib Ace-belt

BANDO 6PJ887

13 mm End of the Box Wrench

Anticlockwise

Peep Window

Line

Arrow

Arm Mounting Nuts

Long Plate

CM14E_WE_all.indb 19CM14E_WE_all.indb 19 2008/02/05 21:09:332008/02/05 21:09:33

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CM14E in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 9,1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi CM14E Manual

Product: