565923

Hitachi CM12Y Manual

7
Zoom out
Zoom in
Previous page
1/48
Next page
6
English
e) Do not attach a saw chain woodcarving blade or
toothed saw blade.
Such blades create frequent kickback and loss of
control.
f) Do not “jam” the wheel or apply excessive pressure.
Do not attempt to make an excessive depth of cut.
Overstressing the wheel increases the loading and
susceptibility to twisting or blinding of the wheel in
the cut and the possibility of kickback or wheel
breakage.
g) When wheel is binding or when interrupting a cut
for any reason, switch off the power tool and hold
the power tool motionless until the wheel comes to
a complete stop. Never attempt to remove the wheel
from the cut while the wheel is in motion otherwise
kickback may occur.
Investigate and take corrective action to eliminate
the cause of wheel binding.
h) Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter
the cut.
The wheel may bind, walk up or kickback if the power
tool is restarted in the workpiece.
i) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near
the line of cut and near the edge of the workpiece on
both sides of the wheel.
j) Use extra caution when making a “pocket cut” into
existing walls or other blind areas.
The protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kickback.
PRECAUTION ON USING DISC CUTTER
1. Never attach any tool except the diamond wheel or
cutting wheel as specified by the manufacturer (see
optional accessories).
Do not operate the cutter while applying water.
2. Always check the diamond wheel before starting the
machine. If it is cracked, broken or bent, do not use
it. Carefully start the machine to check for other
abnormalities.
3. Using the diamond wheel to cut metal will shorten
its service life or will result in breakage. Never use
the diamond wheel to cut metal.
4. Start working only when maximum rotation speed
is reached.
5. Excessive force overloads the motor and reduces
working efficiency and service life. Always cut
concrete, tile or stone with a cutting depth of 50mm
or less. If the cutting depth is more than 50mm,
cut the workpiece 2 or 3 times. If the workpiece is
cut with a cutting depth of more than 50mm, the
service life of the diamond wheel will be reduced
and the motor may seize.
6. Do not use this machine to cut asbestos.
7. In operations using a cutting wheel, if flame comes
out, cover the dust collection adapter with a rubber
cap and be sure to wear protective glasses.
SPECIFICATIONS
Voltage (by areas)* (110V, 230V)
Power input* 2400W
No-load speed 5000 min
–1
Dimensions of diamond wheel
Max. cutting depth 100mm
Weight (without cord and diamond wheel) 11.5kg
*Be sure to check the nameplate on product as it is subject to change by areas.
Outer dia. 305mm
Thickness 2.0mm
Hole dia. 22.2mm/20mm
STANDARD ACCESSORIES
(1) Hose ............................................................................. 1
(2) Wrench ........................................................................ 1
(3) Protective glasses ...................................................... 1
Standard accessories are subject to change without
notice.
01Eng_CM12Y_WE 4/20/10, 13:426
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CM12Y at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CM12Y in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info