565917

Hitachi CL10SA Manual

5
Zoom out
Zoom in
Previous page
1/60
Next page
English
4
2. Trimmer
Optional accessories are subject to change without
notice.
APPLICATIONS
⅜ Cutting of soft steel studs
PRIOR TO OPERATION
WARNING!
Before use, check the following items. Concerning items
1-7, always be sure to check them before plugging the
power cord into the receptacle.
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
CAUTION:
Damaged cord must be replaced or repaired.
4. Preparation and confirmation of working environment.
Check and confirm if the workplace is in proper
conditions as mentioned in the general operational
precautions item 1.
Screw size
M10 × 1.5
M8 × 1.25
M6 × 1
W3/8" × 1.5875
5. Setting the forward/reverse switching button
(1) As illustrated in Fig. 1-1, the forward/reverse
switching button ordinarily lies at the position of
(Fig. 1-1), enabling cutting operation.
(2) If you press in the forward/reverse switching button
from the left as shown in Fig. 1-2 at the position
of
(Fig. 1-2) and slowly pull the trigger switch
while pressing the button, the cutter can be removed
from the stud. Keep the button at this position only
when you remove the cutter from the stud during
cutting operation. As soon as the cutter is removed
from the stud, turn off the switch. If you release your
finger, the forward/reverse switching button will
automatically return to the position of
(Fig. 1-1).
CAUTION
⅜ Do not attempt to cut in the
position (Fig. 1-
2). If you attempt to cut in this position, there will
be an overload on the motor and cutting will not
be possible. Never apply excessive force to the
main unit as this can cause damage to the unit.
⅜ When you operate the forward/reverse-switching
button at the position of
(Fig. 1-2), do not
release your finger from the forward/reverse-
switching button until the switch is turned off. If
you release your finger before the switch is turned
off, there can be a case where the bracket (A) does
not stop immediately.
Fig. 1-1 Fig. 1-2
Forward/reverse switching button
(Equipment as seen from the handle side)
Removal during
cutting operations
During cutting
operations
OPTIONAL ACCESSORIES (sold separately)
1. Cutter
Screw size Combining cutters and spacers
M10 × 1.5 M10 Cutter ............................. 2
M10 Spacer ............................ 2
M8 × 1.25 M8 Cutter ............................... 2
M8 Spacer .............................. 2
M6 × 1 M6 Cutter ............................... 2
M6 Spacer ............................. 2
W3/8" × 1.5875 W3/8" Cutter ........................... 2
01Eng_CL10SA_WE 08/12/15, 11:574
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CL10SA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CL10SA in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info