565914

Hitachi CL10D2 Manual

6
Zoom out
Zoom in
Previous page
1/76
Next page
English
5
Optional accessories are subject to change without notice.
APPLICATIONS
䡬 Cutting of soft steel studs.
BATTERY REMOVAL/INSTALLATION
1. Battery removal
Firmly support the power tool and remove the
battery while pushing the latch of the battery with
your thumb (Fig. 1).
CAUTION:
䡬 Never short-circuit the battery.
䡬 Support the battery with your palm so that it does
not fall down.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 1).
Fig. 1
3. Trimmer
Screw size
M10 × 1.5
M8 × 1.25
M6 × 1
W3/8" × 1.5875
Trigger
switch
Handle
Push
Latch
Insert
Pull out
Rechargeable battery
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger’s power cord to a receptacle.
When the power cord is connected, the charger’s
pilot lamp will blink in red. (At 1-second intervals).
2. Insert the battery into the charger.
Position the battery so that the nameplate faces
toward the caution plate of the charger and push
in the battery until it contacts the bottom plate. (See
Figs. 2 and 3.)
CAUTION:
䡬 If the batteries are inserted in the reverse direction,
not only recharging will become impossible, but it
may also cause the fuse to blow, or problems in
the charger such as a deformed recharging terminal.
3. Charging
When inserting a battery in the charger, charging
will commence and the pilot lamp will light
continuously in red.
When the battery becomes fully recharged, the pilot
lamp will blink in red. (At 1-second intervals.) (See
Table 1)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown
in Table 1, according to the condition of the charger
or the rechargeable battery.
Rechargeable
battery
Hole for connecting
the rechargeable
battery
Pilot lamp
Insert
Nameplate
Rechargeable
battery
Latch
Fig. 2
Fig. 3
01Eng_CL10D2_WE 1/28/08, 17:455
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CL10D2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CL10D2 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info