565908

Hitachi CJ10DL Manual

13
Zoom out
Zoom in
Previous page
1/68
Next page
English
12
carry out pocket cutting quite easily with the saw
blade installed in reverse as illustrated in Fig. 23,
Fig. 25, and Fig. 27. Use the saw blade that is as
short and thick as possible.
(1) Press the lower part (or the upper part) of the base
against the material. Pull the switch trigger while
keeping the tip of the saw blade apart from the
material (Fig. 22, Fig. 23).
(2) Raise the handle slowly and cut in with the saw
blade little by little (Fig. 24, Fig. 25).
(3) Hold the body firmly until the saw blade completely
cuts into the material (Fig. 26, Fig. 27).
CAUTION
⅜ Avoid plunge cutting for metallic materials. This can
easily damage the blade.
⅜ Never pull the switch trigger while the tip of the
saw blade is pressed against the material. If you
do so, the blade can easily be damaged when it
collides with the material.
⅜ Make absolutely sure that you cut slowly while
holding the body firmly. If you apply any
unreasonable force to the saw blade during the
cutting operation, the blade can easily be damaged.
NOTE
The use of the battery BCL1015 in a cold condition
(below 0 degree Centigrade) can sometimes result
in the weakened cutting torque and reduced amount
of work. This, however, is a temporary phenomenon,
and returns to normal when the battery warms up.
6. Battery Level Warning Lamp
The battery level can be checked by pulling the
trigger switch while the power tool is in a no-load
state. The battery level warning lamp lights when
the battery power is very low. If this happens,
charge the battery. (Fig. 5)
NOTE
⅜ The level at which the battery level warning lamp
lights may vary due to the ambient temperature,
characteristics of the battery, etc. and is intended
only as a guide.
⅜ The battery level warning lamp may light when the
power tool is overloaded. This does not mean that
the battery power is very low.
Be sure to check the battery level while the tool
is in a no-load state.
01Eng_CJ10DL_WE 8/3/09, 12:2912
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CJ10DL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CJ10DL in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info