Manual Hitachi CJ 120 VA (page 11 of 60) (English, German, Dutch, French, Italian, Portuguese, Spanish)

110165

Zoom out

Zoom in

1/60

English

1. Adjust the speed

NOTE:

Dial scale reading is for reference only. The higher

the speed is, the quicker the material is cut. But the

service life of the blade will be reduced in this case.

When the speed is too low, cutting will take longer,

although the service life will be prolonged. Make

adjustments as desired.

2. Set the orbital position to “0”

NOTE:

⅜ When cutting use cutting fluid (oil base cutting fluid)

to prolong the blade’s service life.

SELECTION OF BLADES

⅜ Accessory blades

To ensure maximum operating efficiency and results,

it is very important to select the appropriate blade

best suited to the type and thickness of the material

to be cut. Three types of blades are provided as

standard accessories. The blade number is engraved

in the vicinity of the mounting portion of each blade.

Select appropriate blades by referring to Table 1.

HOUSING THE HEXAGONAL BAR WRENCH

It is possible to house the hexagonal bar wrench on the

base. (See Fig. 16)

CONNECTING WITH CLEANER

By connecting with cleaner (sold separately) through dust

collector and adapter (sold separately), most of dust can

be collected.

(1) Remove the hexagonal bar wrench from the base.

(2) Move the base fully forward. (Fig. 9, 10)

(3) Attach the chip cover with the shutter put between

the chip cover and gear cover. (Fig. 17)

(4) Connect the dust collector with adapter. (Fig. 18)

(5) Connect the adapter with the nose of cleaner. (Fig.

18)

(6) Insert dust collector into the rear hole of the base until

the hook catches in the notch. (Fig. 19)

(7) Press the hook to remove the dust collector.

MAINTENANCE AND INSPECTION

1. Inspecting the blade

Continued use of a dull or damaged blade will result

in reduced cutting efficiency and may cause

overloading of the motor. Replace the blade with a

new one as soon as excessive abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws

be loose, retighten them immediately. Failure to do

so could result in serious hazard.

Blade

Thickness of material

Dial Scale

No. 97 1.5 – 2.5 mm

Middle groove position

between scales “2”

and “3”

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes

For your continued safety and electrical shock

protection, carbon brush inspection and replacement

on this tool should ONLY be performed by a HITACHI

AUTHORIZED SERVICE CENTER.

5. Replacing supply cord

If the supply cord of Tool is damaged, the Tool must

be returned to Hitachi Authorized Service Center for

the cord to be replaced.

6. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION:

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

NOTE:

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

IMPORTANT:

Correct connection of the plug

The wires of the main lead and coloured in accordance

with the following code:

Blue: -Neutral

Brown: -Live

As the colours of the wires in the main lead of this tool

may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black.

The wire coloured brown must be connected to the

terminal marked with the letter L or coloured red.

Neither core must be connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

01Eng_CJ120V_WE 08/10/15, 10:4310

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CJ 120 VA in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi CJ 120 VA Manual

Product: