661481
8
Zoom out
Zoom in
Previous page
1/136
Next page
8
English
2. Replacing the blade
For your continued safety, blade inspection and
replacement on this tool should ONLY be performed by
a HITACHI AUTHORIZED SERVICE CENTER.
3. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
4. Replacing supply cord
If the replacement of the supply cord is necessary, it has
to be done by Hitachi Authorized Service Center to avoid
a safety hazard.
5. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
6. Cleaning on the outside
When the hedge trimmer is stained, wipe with a soft dry
cloth or a cloth moistened with soapy water. Do not use
chloric solvents, gasoline or paint thinner, for they melt
plastics.
7. Transport of the tool
Attach the blade case to the blade before carrying this
tool.
If you carry it without the blade case, the blade may
come in contact with your body, causing injury.
8. Storage
Store the hedge trimmer in a place out of reach of
children.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your
dealer or the Hitachi Authorized Service Center.
Symptom Possible cause Remedy
Does not operate. The power plug is not plugged into the
power socket.
Plug the power cord into the power
socket.
Foreign matter is lodged in the blade. When there is foreign matter in the blade,
disconnect the plug from receptacle
and use a pair of tongs or similar tool to
remove it.
Take great care since the tool may start
operating when the foreign matter has
been removed.
Sap or rust may also prevent the blade
from operating. Use a wire brush or similar
tool to remove sap or rust.
The tool does not trim well. The blade has become dull. Use a brush or cloth to remove sap.
If cleaning the blade does not improve
its cutting ability, contact the HITACHI
AUTHORIZED SERVICE CENTER to
have the blade replaced.
The blade stopped because it was used
to cut a branch whose width exceeded the
blade’s cutting capacity.
NOTE
Work that will repeatedly cause the
blade to stop will eventually damage
the motor.
Some garden trees have wood that is very
hard and may be beyond the capacity of
the tool even if it is of a width that is within
normal capacity. Use a pair of pruning
shear to remove thick branches before
starting work.
An oblique cut may also exceed the
capacity of the tool since the length of
the cut increases. Be sure to trim thick
branches at right angles.
0000Book_CH45Y.indb 80000Book_CH45Y.indb 8 2017/03/15 9:52:332017/03/15 9:52:33
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CH65Y at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CH65Y in the language / languages: All languages as an attachment in your email.

The manual is 8,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info