563753
8
Zoom out
Zoom in
Previous page
1/72
Next page
8
English
Air lter (Fig. 8)
The air lter must be cleaned from dust and dirt in order to avoid:
Carburetor malfunctions
Starting problems
Engine power reduction
Unnecessary wear on the engine parts
Abnormal fuel consumption
Clean the air lter daily or more often if working in exceptionally dusty
areas.
Cleaning the air lter
Remove the air lter cover and the lter (10). Rinse it in warm soap
suds. Check that the lter is dry before reassembly. An air lter that has
been used for some time cannot be cleaned completely. Therefore,
it must regularly be replaced with a new one. A damaged lter must
always be replaced.
Fuel lter (Fig. 9)
Drain all fuel from fuel tank and pull fuel lter line from tank. Pull lter
element out of holder assembly and rinse element in warm water with
detergent.
Rinse thoroughly until all traces of detergent are eliminated. Squeeze,
do not wring, away excess water and allow element to air dry.
NOTE
If element is hard due to excessive dirt buildup, replace it.
Spark plug (Fig. 10)
The spark plug condition is in uenced by:
An incorrect carburetor setting
Wrong fuel mixture (too much oil in the gasoline)
A dirty air lter
Hard running conditions (such as cold weather)
These factors cause deposits on the spark plug electrodes, which
may result in malfunction and starting di culties. If the engine is low
on power, di cult to start or runs poorly at idling speed, always check
the spark plug rst. If the spark plug is dirty, clean it and check the
electrode gap. Re-adjust if necessary. The correct gap is 0.6 mm.
The spark plug should be replaced after about 100 operation hours or
earlier if the electrodes are badly eroded.
NOTE
In some areas, local law requires using a resistor spark plug
to suppress ignition signals. If this machine was originally
equipped with resistor spark plug, use same type of spark plug for
replacement.
Mu er (Fig. 11)
Remove the mu er and clean out any excess carbon from the exhaust
port or mu er inlet every 100 hours of operation.
Cylinder (Engine cooling) (Fig. 12)
The engine is air cooled, and air must circulate freely around engine
and over cooling ns on cylinder head to prevent overheating.
Every 100 operating hours, or once a year (more often if conditions
require), clean ns and external surfaces of engine of dust, dirt and oil
deposits which can contribute to improper cooling.
NOTE
Do not operate engine with engine shroud or mu er guard
removed as this will cause overheating and engine damage.
Maintenance schedule
Below you will nd some general maintenance instructions. For further
information please contact your Hitachi dealer.
Daily maintenance
Clean the exterior of the unit.
Check that the harness is undamaged.
Check that nuts and screws are su ciently tightened.
Weekly maintenance
Check the starter, especially the cord and return spring.
Clean the exterior of the spark plug.
Remove it and check the electrode gap. Adjust it to 0.6 mm, or
change the spark plug.
Clean the cooling ns on the cylinder and check that the air intake
at the starter is not clogged.
Clean the air lter
Monthly maintenance
Rinse the fuel tank with gasoline.
Clean the exterior of the carburetor and the space around it.
Clean the fan and the space around it.
000Book_CG22EJ(SLN).indb 8000Book_CG22EJ(SLN).indb 8 2012/06/21 15:30:192012/06/21 15:30:19
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CG27EJ-SLNP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CG27EJ-SLNP in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info