563764

Hitachi CG27EBSP-SLN Manual

10
Zoom out
Zoom in
Previous page
1/88
Next page
10
English
ASSEMBLY PROCEDURES
Drive shaft to engine (Fig. 1)
Loosen tube locking bolt (1) about ten turns so that the bolt point will
not obstruct drive shaft tube to be inserted. When inserting drive
shaft tube, hold the tube locking bolt outward preventing inside
fi tting from obstructing as well.
Insert the drive shaft into the clutch case of the engine properly until
the marked position (2) on the drive shaft tube meets the clutch
case.
Some models may come with the drive shaft already installed.
NOTE
When it is hard to insert drive shaft up to the marked position on
the drive shaft tube, turn drive shaft by the cutter mounting end
clockwise or counter-clockwise. Tighten tube locking bolt lining
up the hole in the shaft tube. Then tighten clamp bolt securely.
Installation of attachment
1. Join the attachment in place of it.
2. Make sure the lock pin (3) fi ts in the location hole (4) of tube and
that the tube will not come off . (Fig. 2)
3. Tighten the knob nut (5) securely. (Fig. 2)
Model
CG27EBSP CG27EBDP
(SL) (S) (SL) (SLN)
Engine
Displacement (cm
3
)
Spark plug
Idling speed (min
-1
)
Speed of output shaft (min
-1
)
Max. engine output (kW)
26.9
NGK BMR7A
2800 – 3200
7600
0.9
26.9
NGK BMR7A
2800 – 3200
7600
0.9
26.9
NGK BMR7A
2800 – 3200
7600
0.9
26.9
NGK BMR7A
2800 – 3200
7600
0.9
Fuel tank capacity (cm
3
)520
Dry weight (kg) 5.2 5.4 5.4 4.5
Cutting attachment Type / Dia. (mm) Nylon cord Nylon cord
Metal blade
(255)
Nylon cord ------
Sound pressure
level LpA
(dB (A))
(ISO22868)
Equivalent*
Uncertainty
86
3
86
3
85
3
86
3
86
3
Measured sound
power level LwA (dB (A))
Guaranteed sound
power level LwA (dB (A))
(2000/14/EC)
Racing
(2000/14/EC)
Racing
108
111
108
111
108
111
108
111
------
------
Vibration level (m/s
2
) (ISO22867)
Equivalent (Front / Left handle)*
Equivalent (Rear / Right handle)*
Uncertainty
6.7
4.1
2.0
4.1
3.0
1.2
3.7
2.6
1.2
5.3
3.4
2.0
------
------
------
NOTE
Equivalent noise level/vibration level are calculated as the time-weighted energy total for noise/vibration levels under various
working conditions with the following time distribution:
* 1/2 Idle, 1/2 racing.
All data subject to change without notice.
Installation of handle
WARNING
Always use a barrier bar (6) and shoulder harness with the loop
handle. (Fig. 3)
Attach the handle to the drive shaft tube with the angle towards the
engine.
Adjust the location to the most comfortable position before
operation.
NOTE
If your unit has handle location label on drive shaft tube, follow
the illustration.
Remove the handle bracket (7) from the assembly. (Fig. 4)
Place the handles and attach the handle bracket with four bolts
lightly. Adjust to appropriate position. Then attach it fi rmly with the
bolts.
Attach the protection tube to the drive shaft or handle using cord
clamps (8). (Fig. 5)
000Book_CG24EBSP_WE.indb 10000Book_CG24EBSP_WE.indb 10 2014/03/26 11:22:062014/03/26 11:22:06
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CG27EBSP-SLN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CG27EBSP-SLN in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 10,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info