563763
13
Zoom out
Zoom in
Previous page
1/88
Next page
13
English
WARNING
When the engine is idling the cutting attachment must under no
circumstances rotate.
Air lter (Fig. 29)
The air lter must be cleaned from dust and dirt in order to avoid:
Carburetor malfunctions
Starting problems
Engine power reduction
Unnecessary wear on the engine parts
Abnormal fuel consumption
Clean the air lter daily or more often if working in exceptionally
dusty areas.
Cleaning the air lter
Open the air lter cover and the lter (29). Rinse it in warm soap
suds. Check that the lter is dry before reassembly. An air lter
that has been used for some time cannot be cleaned completely.
Therefore, it must regularly be replaced with a new one. A damaged
lter must always be replaced.
Fuel lter (Fig. 30)
Drain all fuel from fuel tank and pull fuel lter line from tank. Pull
lter element out of holder assembly and rinse element in warm
water with detergent.
Rinse thoroughly until all traces of detergent are eliminated.
Squeeze, do not wring, away excess water and allow element to air
dry.
NOTE
If element is hard due to excessive dirt buildup, replace it.
Spark plug (Fig. 31)
The spark plug condition is in uenced by:
An incorrect carburetor setting
Wrong fuel mixture (too much oil in the gasoline)
A dirty air lter
Hard running conditions (such as cold weather)
These factors cause deposits on the spark plug electrodes, which
may result in malfunction and starting di culties. If the engine
is low on power, di cult to start or runs poorly at idling speed,
always check the spark plug rst. If the spark plug is dirty, clean it
and check the electrode gap. Re-adjust if necessary. The correct
gap is 0.6 mm. The spark plug should be replaced after about 100
operation hours or earlier if the electrodes are badly eroded.
NOTE
In some areas, local law requires using a resistor spark plug
to suppress ignition signals. If this machine was originally
equipped with resistor spark plug, use same type of spark plug
for replacement.
Angle transmission (Fig. 32)
Check angle transmission or angle gear for grease level about every
50 hours of operation by removing the grease ller plug on the side
of angle transmission.
If no grease can be seen on the anks of the gears, ll the
transmission with quality lithium based multipurpose grease up to
3/4. Do not completely ll the transmission.
Semi-auto cutting head
Nylon line replacement
(1) Remove the case (30) by rmly pushing inward the locking tabs
with your thumbs as shown in Fig. 33.
(2) After removing the case, take out the reel and discard the
remaining line.
(3) Fold the new nylon line unevenly in half as shown in picture.
Hook the U-shaped end of the nylon line into the groove (31) on
the center partition of the reel.
Wind both halves of the line on the reel in the same direction,
keeping each half of the line on its own side of the partition.
(Fig. 34)
(4) Push each line into the stopper holes (32), leaving the loose
ends approx. 10 cm in length. (Fig. 35)
(5) Insert both loose ends of the line through the cord guide (33)
when placing the reel in the case. (Fig. 36)
NOTE
When placing a reel in the case, try to line up the stopper holes
(32) with the cord guide (33) for easier line release later.
(6) Place the cover over the case so that the cap locking tabs (34)
on the case meet the long holes (35) on the cover. Then push
the case securely until it clicks into place. (Fig. 37)
(7) The initial cutting line length should be approx. 1114 cm and
should be equal on both sides. (Fig. 38)
Blade (Fig. 39)
WARNING
Wear protective gloves when handling or performing
maintenance on the blade.
Use a sharp blade. A dull blade is more likely to snag and
thrust. Replace the fastening nut if it is damaged and hard to
tighten.
When replacing blade, purchase one recommended by Hitachi,
with a 25.4 mm (one inch) tting hole.
In the case of a 3 tooth blade (36), it can be used on either side.
Use the correct blade for the type of work.
When replacing blades, use appropriate tools.
When cutting edges become dull, re-sharpen or le as shown
in the illustration. Incorrect sharpening may cause excessive
vibration.
Discard blades that are bent, warped, cracked, broken or
damaged in any way.
NOTE
When sharpening blade it is important to maintain an original
shape of radius at the base of the tooth to avoid cracking.
Maintenance schedule
Below you will nd some general maintenance instructions. For
further information please contact Hitachi Authorized Service
Centers.
Daily maintenance
Clean the exterior of the unit.
Check that the harness is undamaged.
Check the cutting attachment guard for damage or cracks.
Change the guard in case of impacts or cracks.
Check that the cutting attachment is properly centred, sharp,
and without cracks. An o -centre cutting attachment induces
heavy vibrations that may damage the unit.
Check that the cutting attachment nut is su ciently tightened.
Make sure that the blade transport guard is undamaged and
that it can be securely tted.
Check that nuts and screws are su ciently tightened.
Check that the unit is undamaged and free of defects.
Weekly maintenance
Check the starter, especially the cord and return spring.
Clean the exterior of the spark plug.
Remove it and check the electrode gap. Adjust it to 0.6 mm, or
change the spark plug.
Check that the angle gear is lled with grease up to 3/4.
Clean the air lter.
Monthly maintenance
Rinse the fuel tank with gasoline.
Clean the exterior of the carburetor and the space around it.
Clean the fan and the space around it.
000Book_CG24EBSP_WE.indb 13000Book_CG24EBSP_WE.indb 13 2014/03/26 11:22:072014/03/26 11:22:07
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CG27EBDP-SL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CG27EBDP-SL in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 10,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info