Manual Hitachi CG25EUS (page 9 of 64) (English, German, Dutch, French, Italian, Portuguese, Spanish)

563769

Zoom out

Zoom in

1/64

English

SPECIFICATIONS

Model

CG25EUS

CG25EUS (L)

Engine Size (mℓ)25

Spark Plug

NGK CMR5H

or equivalent

Fuel Tank Capacity (ℓ)0.55

Engine Oil Capacity (mℓ)80

Dry Weight (kg)

CG2 5 EUS .........5. 2

CG25EUS (L) ...5.0

Sound pressure level

LpA (dB (A))

(EN27917)

81.8 78.6

Measured sound power

level LwA (dB (A))

Guaranteed sound

power level LwA (dB (A))

101.8 98.6

104 101

Vibration level (m/s

)

(ISO7916)

CG25EUS

Left handle

Right handle

CG25EUS (L)

Front handle

Rear handle

4.8 5.4

4.7 4.8

4.8 4.5

3.2 4.6

NOTE

Equivalent noise level/vibration level are calculated as the time-

weighted energy total for noise/vibration levels under various

working conditions with the following time distribution: 1/2 Idle,

1/2 racing.

* All data subject to change without notice.

ASSEMBLY PROCEDURES

Drive shaft to engine (Fig. 1)

Loosen tube locking bolt (1) so that the bolt point will not obstruct

drive shaft tube to be inserted. When inserting drive shaft tube,

hold the tube locking bolt outward preventing inside ﬁ tting from

obstructing as well.

Insert the drive shaft into the clutch case of the engine properly until

the marked position (2) on the drive shaft tube meets the clutch

case.

NOTE

When it is hard to insert drive shaft up to the marked position on

the drive shaft tube, turn drive shaft by the cutter mounting end

clockwise or counter-clockwise. Tighten tube locking bolt lining

up the hole in the shaft tube. Then tighten clamp bolt securely

(3).

Installation of handle

WARNING

When you use steel/rigid blades on straight shaft trimmers or

brush cutters, always use a barrier bar (4) and shoulder harness

with the loop handle. (Fig. 2)

Attach the handle to the drive shaft tube with the angle towards the

engine.

Adjust the location to the most comfortable position before

operation.

NOTE

If your unit has handle location label on drive shaft tube, follow

the illustration.

Remove the handle bracket (5) from the assembly. (Fig. 3)

Place the handles and attach the handle bracket with four bolts

lightly. Adjust to appropriate position. Then attach it ﬁ rmly with the

bolts.

Attach the protection tube to the drive shaft or handle using cord

clamps (6). (Fig. 4)

Throttle wire / stop cord (Fig. 6)

Remove air cleaner cover. (Fig. 5)

Connect stop cords. (Fig. 7)

If the throttle outer end (7) is threaded on your unit, screw it into the

cable adjuster stay (8) all the way, and then tighten this cable end

using the adjuster nut (9) against the cable adjuster stay (8).

Connect throttle wire end (10) to carburetor (11) and install swivel cap

(if so equipped) where is included in tool bag, onto swivel.

Attach the air cleaner cover.

Installation of blade guard (Fig. 8)

NOTE

The guard bracket may come already mounted to the gear case

on some models.

Install the blade guard on drive shaft tube against angle

transmission. Tighten the guard bracket ﬁ rmly so that the blade

guard does not swing or move down during operation.

CAUTION

Some blade guards are equipped with sharp line limiters. Be

careful with handling it.

When using a trimmer head with two piece type blade guard, attach

the guard extension to the blade guard. (Fig. 9)

NOTE

○ When attaching the guard extension to the blade guard, the

sharp line limiter must be removed from the blade guard, (if so

installed).

000Book_CG25EUS_WE.indb 9000Book_CG25EUS_WE.indb 9 2009/12/25 21:39:072009/12/25 21:39:07

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CG25EUS in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 8,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi CG25EUS Manual

Product: