616693
8
Zoom out
Zoom in
Previous page
1/220
Next page
8
English
MOUNTING AND OPERATION
Action Figure Page
Removing and inserting the battery 2 205
Charging 3 205
Switch operation 4 206
Regarding the switch panel
(Remaining battery indicator)
5 206
Regarding the rotation mechanism of
the tool head
6 206
Cutting 7 207
If the tool bites into a rebar 8 208
Changing the cutter block* 9 208
How to replenish the hydraulic oil 10 209
Check and replacing the carbon brush 11 210
Selecting accessories 211
* Changing the cutter block
With repeated rebar cutting, the cutter block will sustain
damage such as blade wear, deformation or chipping.
When a worn, deformed or chipped cutter block is
used, the piston may not return due to the rebar not
being fully cut and remaining sandwiched by the cutter
block. Furthermore, this could lead to tool malfunction or
damage to the cutter block.
1000 cuts per single blade location
The life (number of cuts) of a single location on the
blade is approximately 1000.
4 blade locations on a single cutter block
There are 4 blade locations on the cutter block which
can be used by re-attaching and changing the facing
of the block 4 times.
Change the cutter block as early as possible
Change the facing of the cutter block or exchange it if
the blade is chipped or deformed.
Blade
Deformation/
Chipping
MAINTENANCE AND INSPECTION
1. Maintenance after use
After using the tool, put on a pair of leather gloves and
clean o the metal particles and other waste matter
around the piston.
NOTE
Metal particle buildup can cause the piston to seize up.
WARNING
Do not blow away the waste matter with an airgun or
similar tool.
Sharp-edged fragments can cause injury when scattered
in the air.
2. Check the cutter block
Periodically check the blade for chipping or deformation.
WARNING
Replace the blade at an early stage. Using a chipped
or deformed blade could result in injury from ying
fragments.
3. Check hydraulic oil volume
Over 70% of reduced cutting power is the result of
insu cient hydraulic oil volume. Before using the tool,
always check the hydraulic oil volume.
4. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
5. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
6. Inspecting the carbon brushes (Fig. 11)
The motor employs carbon brushes which are
consumable parts. Since and excessively worn carbon
brush with new ones when it becomes worn to or near
the “wear limit” . In addition, always keep carbon
brushes clean and ensure that they slide freely whithin
the brush holders.
NOTE
When replacing the carbon brush with a new one, be
sure to use the Hitachi Carbon Brush Code No. 999100.
7. Replacing carbon brushes (Fig. 11)
Take out the carbon brush by rst removing the brush
cap and then hooking the protrusion of the carbon brush
with a at head screw driver, etc.
When installing the carbon brush, choose the direction
so that the nail of the carbon brush agrees with the
contact portion outside the brush tube. Then push it in
with a nger. Lastly, install the brush cap.
CAUTION
Be absolutely sure to insert the nail of the carbon brush
into the contact portion outside the brush tube. (You can
insert whichever one of the two nails provided).
Caution must be exercised since any error in this
operation can result in the deformed nail of the carbon
brush and may cause motor trouble at an early stage.
8. Cleaning on the outside
When the power tool is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use chloric
solvents, gasoline or paint thinner, for they melt plastics.
9. Storage
Storing in a place below 40°C and out of the reach of
children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, signi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
Important notice on the batteries for the Hitachi
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used with
batteries other than these designated by us, or when
the battery is disassembled and modi ed (such as
disassembly and replacement of cells or other internal
parts).
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CF18DSAL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CF18DSAL in the language / languages: All languages as an attachment in your email.

The manual is 26,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info