382481
8
Zoom out
Zoom in
Previous page
1/42
Next page
7
English
STANDARD ACCESSORIES
(1) Saw Blade (mounted on tool ) .................................. 1
(Dia. 235 mm)
(2) Box Wrench ................................................................ 1
(3) Guide ........................................................................... 1
(4) Wing-bolt .................................................................... 1
(5) Side Handle ................................................................. 1
(6) Flat Hd. Screw M6 × 16 .............................................. 2
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
(1) Dust Collector Set
Connect the suction hose to collect saw dust with the
vacuum cleaner (see Fig. 12).
(2) Washer (A) ... for 16 mm (Hole dia. of saw blade)
... for 20 mm (Hole dia. of saw blade)
... for 30 mm (Hole dia. of saw blade)
Optional accessories are subject to change without notice.
APPLICATION
Cutting various types of wood.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Prepare a wooden workbench (Fig. 1)
Since the saw blade will extend beyond the lower
surface of the lumber, place the lumber on a
workbench when cutting. If a square block is utilized
as a workbench, select level ground to ensure it is
properly stabilized. An unstable workbench will result
in hazardous operation.
SPECIFICATIONS
5. When using the side handle (Fig. 2)
Securely attach the side handle to the base with the
two flat head screws (M6 × 16) when using the side
handle.
CAUTION
To avoid possible accident, always ensure that the portion
of lumber remaining after cutting is securely anchored
or held in position.
ADJUSTING THE SAW PRIOR TO USE
1. Adjusting the cutting depth
As shown in Fig. 3, hold the handle with one hand
while loosening the knob with the other.
The cutting depth can be adjusted by moving the
base to the desired position. In such manner adjust
the cutting depth and then securely retighten the
knob.
2. Adjusting the riving knife
Loosen the hexagonal head bolt used to clamp the
riving knife, adjust the riving knife to the position
shown in Fig. 4 and securely retighten the bolt. After
adjustment, ensure that riving knife moves in
accordance with the adjusted cutting depth.
3. Adjusting the angle of inclination
As shown in Fig. 5 (A), Fig. 5 (B) by loosening the
knob on the incline gauge and the wing-bolt on the
base, the saw blade may be inclined to a maximum
angle of 45° in relation to the base. After having
completed the adjustment, reconfirm that the knob
and the wing bolt are firmly tightened.
4. Regulating the guide (Fig. 6)
The cutting position can be regulated by moving the
guide to the left or right after loosening its wingbolt.
The guide may be mounted on either the right or left
side of the tool.
CUTTING PROCEDURES
1. Place the saw body (base) on the lumber, and align
the marked off line with the saw blade by use of the
front scale. When the saw blade is not inclined, the
right-hand side is the reference (Fig. 7(A)); when the
saw blade is inclined (45°), the left-hand side marked
45 on the base) is the reference (Fig. 7(B)).
2. Ensure that the switch is turned to the ON position
before the saw blade comes in contact with the
lumber. The switch is turned ON when the trigger is
squeezed; and OFF when the trigger is released.
3. Moving the saw straight at a constant speed will
produce optimum cutting.
*Be sure to check the nameplate on product as it is subject to change by areas.
Model C 9U
Voltage (by areas)* (110V, 220V, 230V, 240V)
Cutting Depth
90°0 86 mm
45°Max. 65 mm
Power Input* 1750W
No-Load Speed 5000 min1
Weight (without cord) 7.1 kg
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi c9u at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi c9u in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi c9u

Hitachi c9u User Manual - English, Danish, Swedish, Norwegian, Finnish - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info