Manual Hitachi c9u (page 23 of 30) (English, Danish, Swedish, Norwegian, Finnish)

382481

Zoom out

Zoom in

1/30

English

STANDARD ACCESSORIES

(1) Saw Blade (Dia. 235 mm)(mounted on tool) ........ 1

(2) Box Wrench ............................................................... 1

(3) Guide .......................................................................... 1

(4) Wing-bolt ................................................................... 1

(5) Side Handle ............................................................... 1

(6) Flat Hd. Screw M6 × 16 ........................................... 2

Standard accessories are subject to change without no-

tice.

OPTIONAL ACCESSORIES (sold separately)

(1) Dust Collector Set

Connect the suction hose to collect saw dust with

the vacuum cleaner (see Fig. 12).

(2) Washer (A)

... for 16

mm (Hole dia. of saw blade)

... for 20 mm (Hole dia. of saw blade)

... for 30 mm (Hole dia. of saw blade)

Optional accessories are subject to change without notice.

APPLICATION

Cutting various types of wood.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Prepare a wooden workbench (Fig. 1)

Since the saw blade will extend beyond the lower

surface of the lumber, place the lumber on a

workbench when cutting. If a square block is utilized

as a workbench, select level ground to ensure it

is properly stabilized. An unstable workbench will

result in hazardous operation.

5. When using the side handle (Fig. 2)

Securely attach the side handle to the base with

SPECIFICATIONS

the two flat head screws (M6 × 16) when using the

side handle.

CAUTION

To avoid possible accident, always ensure that the por-

tion of lumber remaining after cutting is securely an-

chored or held in position.

ADJUSTING THE SAW PRIOR TO USE

1. Adjusting the cutting depth

As shown in Fig. 3, hold the handle with one hand

while loosening the knob with the other.

The cutting depth can be adjusted by moving the

base to the desired position. In such manner adjust

the cutting depth and then securely retighten the

knob.

2. Adjusting the riving knife

Loosen the hexagonal – head bolt used to clamp

the riving knife, adjust the riving knife to the position

shown in Fig. 4 and securely retighten the bolt.

After adjustment, ensure that riving knife moves in

accordance with the adjusted cutting depth.

3. Adjusting the angle of inclination

As shown in Fig. 5 (A), Fig. 5 (B) by loosening the

knob on the incline gauge and the wing-bolt on the

base, the saw blade may be inclined to a maximum

angle of 45° in relation to the base. After having

completed the adjustment, reconfirm that the knob

and the wing bolt are firmly tightened.

4. Regulating the guide (Fig. 6)

The cutting position can be regulated by moving

the guide to the left or right after loosening its

wingbolt. The guide may be mounted on either the

right or left side of the tool.

CUTTING PROCEDURES

1. Place the saw body (base) on the lumber, and align

the marked off line with the saw blade by use of

the front scale. When the saw blade is not inclined,

the right-hand side is the reference (Fig. 7(A)); when

the saw blade is inclined (45°), the left-hand side

marked “45” on the base) is the reference (Fig.

7(B)).

2. Ensure that the switch is turned to the ON position

before the saw blade comes in contact with the

lumber. The switch is turned ON when the trigger

is squeezed; and OFF when the trigger is released.

3. Moving the saw straight at a constant speed will

produce optimum cutting.

CAUTIONS

⅜ Before starting to saw, ensure that the saw blade

has reached full speed revolution.

*Be sure to check the nameplate on product as it is subject to change by areas.

Model C9U

Voltage (by areas)*

(110V, 220V, 230V, 240V)

Cutting Depth 90° 0

–

86 mm

45° Max. 65 mm

Power

Input*

1750W

No-Load Speed

5000 min

–1

Weight (without cord) 7.1 kg

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi c9u in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 5,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi c9u

Hitachi c9u User Manual - English, German, Dutch, French, Italian, Portuguese, Spanish - 42 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi c9u Manual

Product: