661455
5
Zoom out
Zoom in
Previous page
1/144
Next page
5
English
V
Rated voltage
Cutting depth
P
Power Input
n
0
No-Load speed
kg
Weight (without cord)
Switching ON
Switching OFF
Disconnect mains plug from electrical outlet
Blower
Prohibited action
Class II tool
Brake
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package
contains the accessories listed in the below.
Saw Blade (Dia. 235 mm) (mounted on tool) ................1
Hex. Bar wrench (mounted on tool) ..............................1
Guide ...........................................................................1
Wing-bolt ......................................................................1
Lock Spring ..................................................................1
Lever (short type) .........................................................1
Dust collector ...............................................................1
Side Handle .................................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
Cutting various types of wood.
SPECIFICATIONS
The speci cations of this machine are listed in the Table on
page 133.
NOTE
Due to HITACHI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action Figure Page
Mounting the side handle 2 134
Adjusting the cutting depth 3 134
Adjusting the riving knife 4 134
Adjusting the angle of inclination 5 134
Regulating the guide 6 134
Adjusting the guide piece 7 135
Cutting line 8 135
Switch operation*
1
9 135
Dismounting the saw blade 10 135
Cutting (Do not use the tool with
only the blower function.)
11 136
Using the cord holder 12 136
Mounting the Saw Blade*
2
13 136
Mounting the dust collector set 14 137
Adjusting the base and saw blade
to maintain perpendicularity
15 137
Selecting accessories 138
*1 Before beginning work, check to ensure that operating
the switch correctly turns the tool ON and OFF.
While the tool is plugged in to the receptacle, ensure that
the sawblade stops when the switch is turned OFF.
*2 Usable sawblade diameter: 235 mm
Body thickness: up to 1.6 mm, tip width: at least 1.9 mm
Riving knife thickness: 1.8 mm
MAINTENANCE AND INSPECTION
1. Inspecting the saw blade
Since use of as dull saw blade will degrade e ciency
and cause possible motor malfunction, sharpen or
replace the saw blade as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Inspecting the carbon brushes (Fig. 16)
The motor employs carbon brushes which are consumable
parts. Since an excessively worn carbon brush can result
in motor trouble, replace the carbon brushes with new
ones having the same carbon brush No. shown in the
gure when it becomes worn to or near the “wear limit” .
In addition, always keep carbon brushes clean and ensue
that they slide freely within the brush holders.
CAUTION
When replacing the new carbon brushes, always
use genuine Hitachi carbon brushes with the number
speci ed in the drawing.
For model C9BU3, the brake may not work if other than
the speci ed carbon brushes are used.
When the brake becomes ine ective, replace the carbon
brushes with new ones.
4. Replacing carbon brushes
Disassemble the brush caps with a slotted-head
screwdriver. The carbon brushes can then be easily
removed.
5. Replacing supply cord
If the replacement of the supply cord is necessary, this
has to be done by the manufacturer of this agent in order
to avoid a safety hazard.
6. Motor unit maintenance
The motor winding is an important part of this tool. Avoid
damaging and be careful to avoid contact with cleaning
oil or water.
After 50 hours of use, clean the motor by blowing into the
ventilation holes of the motor housing with dry air from an
air gun or other tool (Fig. 17).
Dust or particle accumulation in the motor can result in
damage.
0000Book_C9U3.indb 50000Book_C9U3.indb 5 2016/10/13 12:21:282016/10/13 12:21:28
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi C9BU3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi C9BU3 in the language / languages: All languages as an attachment in your email.

The manual is 13,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info