54287
15
Zoom out
Zoom in
Previous page
1/18
Next page
ENGLISH - 14 -
Personal Preferences (PP)
All the preset values will be restored, when pressing "PP".
Sound Indicator
This is a stereo option. The alternatives of the indicator are
Mono, Stereo, Dual I and Dual II. This indicator is displayed
under the programme number indicator on the screen. "I-II"
button is used to select Mono or Stereo, or Dual I or Dual II.
In Mono broadcast or in forced-mono (for stereo broadcast).
In Stereo broadcast.
If dual broadcast detected. Dual I is selected in default and also
can be selected after Dual II by Remote Control.
If Dual II selected by Remote Control.
Picture Mode
The picture mode OSD is displayed below the sound indicator,
by TV Status OSDs. According to the WSS data, inside of the
OSD box 4:3, 16:9, 14:9, CINE, SUBT or AUTO is writ-
ten.
By pressing 
 button (if Teletext is not active) the picture
mode can be switched into 4:3, 16:9, 14:9, Cinema, Subtitle or
Auto Mode.
Sleep Timer Last Minute Indicator
It is displayed on the upper right of the screen. If sleep timer is
activated it is displayed with the TV status and erased with it after
3 seconds.
If there is only one minute of the countdown left of the timer, it
is displayed automatically on the upper left of the screen, and
stayed there until finishing. Then TV goes automatically to
stand-by.
Mute Indicator
It is placed in the upper middle of the screen when enabled, and
it stays there until it is disabled.
To cancel mute, there are two alternative; the first one is press-
ing to "
" button, thus volume is set to the preceding value, and
the second one is increasing the volume level, thus it starts at
the minimum level to increase. By decreasing the volume level
in mute state, mute will not be ignored, only the volume level will
decrease. If mute is cancelled after decreasing the volume level,
the volume will return at the decreased level.
No-Signal
No-Signal Timer Indicator
It is displayed in the middle of the screen when no valid signal
detected. It shows the time remaining before the switching to the
Stand-By mode (it takes 5 minutes when no signal detected or
no any Remote Control command is accessed). The indicator
is displayed for 3 seconds when there is no valid signal.
After an Remote Control command (if No-Signal Timer is active)
the timer stops and if no signal detected again the timer is ini-
tialized to 5 minutes and starts 3 seconds later again to count
down.
It is not valid in AV mode.
Blue Background During No-Signal
In case, no valid signal is detected (in TV or AV mode) Blue
Background is activated.During search process Blue Back-
ground is not active. But instead there is another feature given;
the semi-transparent menu background is made blue.
Volume Bar
It is displayed in the lower middle of the screen. When a volume
command is received (pressing Vol+ or Vol- by Remote
Control or Front panel) and no menu is active, it stays on the
screen for 3 seconds, after the last volume command or until
another command is received in between.
AV Modes
By pressing the   button you can switch your TV to AV
modes (except being in Teletext). Pressing this button will
consecutively switch the TV in one of the optional AV modes:
AV-1, AV-2, F-AV (Front AV), RGB (EXT.1) or SVHS (EXT.2).
AV-1 supports the RGB mode and AV-2 supports SVHS mode
unless there is an SVHS socket.
In order to quit the AV mode press the 
 button.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi C32W460N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi C32W460N in the language / languages: English as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi C32W460N

Hitachi C32W460N User Manual - Dutch - 19 pages

Hitachi C32W460N User Manual - French - 20 pages

Hitachi C32W460N User Manual - Italian - 18 pages

Hitachi C32W460N User Manual - Swedish - 18 pages

Hitachi C32W460N User Manual - Spanish - 19 pages

Hitachi C32W460N User Manual - Norwegian - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info