635116
37
Zoom out
Zoom in
Previous page
1/43
Next page
ENGLISH
37
TROUBLESHOOTING
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact
your dealer.
Symptom Point to check See page
• No picture with the power-indicating
lamp off.
• Check the way the power cord is connected.
• Press the power switch.
23
24
• The message “No Input Signal. Going to
suspend” or “Power Save” is displayed.
• No picture with the power indicating lamp
lights in orange.
No input signal is detected.
• Check the way the signal cable is connected.
• Make sure that the switch of the computer, imaging
equipment, etc., is turned on.
• Make sure the computer is not in the power-save mode.
• Check to see if the input selection matches the connection
terminal.
22
• The message “No Input Signal. Going to
sleep” is displayed.
An input signal is not received normally.
• Check to see if the input signal matches the
specifications.
• Check the way the signal cable is connected.
22
40
• The power indicating lamp is normally lit
but no picture.
• Check the contrast and brightness settings (adjust them for
higher contrast and brightness).
• Check the way the signal cable is connected.
19
28
• The display image appears flowing
slantwise.
• Text displayed across the screen
appears vertically streaked, with the
characters in vertical columns blurred.
• Adjust the dot clock frequency and phase. (Adjust the dot
clock frequency first, the dot clock phase next.)
(PC RGB input)
29
42
• Text displayed across the screen
appears blurred.
• A fine pattern flickers when displayed on
the screen.
• Adjust the dot clock phase for the clearest viewing.
(PC RGB input)
29
42
• The remote control does not work.
• Check to see if the batteries are loaded in the remote
control in opposite direction.
• Check to see if the batteries in the remote control are OK.
11
• The display image does not appear in
the normal position.
• Check to see if the displayed input signal match the PDP
TV specification by pressing RECALL button.
• Turn off the Move screen.
31
40
• The display has lack of picture around
the screen.
(PC RGB input)
• Turn off the Move screen.
31
• The temperature of the display panel surface is high. • The plasma display panel is lighting the phosphors by the
discharge of internal radiation. In some cases, this may
cause the temperature of the panel surface to increase.
Please note that this is not a malfunction.
-
Customer servicing can be hazardous.
No Input Signal
No Input Signal
ATTENTION
Using YP
B
P
R
& YC
B
C
R
signals:
• When the input signal is switched he TV might spend time on the display of the new picture. This is normal operation, and no
failures.
• When you select the wrong searching type whatever the input signal is YP
B
P
R
or YC
B
C
R
, the input searching type will be changed to
correct one automatically after 10 seconds searching.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi 42PD7300TA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi 42PD7300TA in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info