560372
19
Zoom out
Zoom in
Previous page
1/42
Next page
13
Basic Features
1. Make sure that you have:
Installed the remote control batteries.
Connected an antenna or cable.
Connected the power cord.
Matched the remote control with TV.
2. Press [POWER ] button to turn on your TV. The Setup
Wizard menu displays.
3. Press [▲/
] to select your menu language: English,
Spanish or French, press [ENTER] button to confirm.
4.
Press [▲/
] to select your Picture Mode: Home Mode or
Retail Mode, press [ENTER] button to confirm.
If you select Retail Mode, a message appears “Please
reconfirm Retail Mode” Select “Yes” to continue, or select
“No” to change your selection.
IMPORTANT: At first, you have to match the remote
control with TV.
To turn your TV on or off (standby mode):
1.
Plug the power cord into an AC power outlet.
2.
Press [POWER] button, your TV turns on.
3.
Press [POWER] button again to turn off your TV. When
you turn off your TV, it goes into standby mode.
The Setup Wizard menu appears the first time you turn
on the TV. It will assist you to specify the menu language,
Picture Mode, Tuner Mode and Channel Installation.
IMPORTANT: Make sure that the antenna or cable is
connected and a wired or wireless Internet connection is
available.
Turning the TV On for the First Time
Turning the TV on or off
If you selected Retail Mode, Energy Saving is not
realized.
5. Press [▲/
] to select your Tuner Mode: Antenna or
Cable, press [ENTER] button to confirm.
6. Press [▲/
] to set the Channel Installation: Search or
Skip Search, press [ENTER] button to confirm.
If you select “Search”, your TV automatically starts
Channel Installation available in your viewing area.
If you select “Skip Search”, your TV does not scan for
channels.
Depending on the reception condition, it may take up to
25 minutes or more to complete memorizing channels.
Please allow the process to complete without interruption.
WARNING
When your TV is in standby mode, it is still receiving
power. To completely disconnect power, unplug the power
cord.
NOTE
If your TV does not receive an input signal for several
minutes, it automatically goes into standby mode.
EXIT
Choose your menu Language
English
Español
Français
Select Next Exit
EXIT
Please connect cable or antenna
Preparing Channel List Status:Searching...
ATV Channels added: 0
DTV Channels added: 0
Exit
8%
The first time you turn on your TV, you
must select the TV signal source. Your
TV stores this information, so you do not
need to change the TV signal source
unless it changes. For example, you
change from an outside antenna to cable
TV.
To select the video input source:
1. Turn on your TV, then press [INPUT]
button on the remote or on the TV. The
Input Source menu opens.
2. Press [▲/
] button to highlight the
input source, then press [ENTER]
button.
Selecting the Input Source
Back Select Next Exit
EXIT
Choose your Picture Mode
Home mode
Retail mode
Home mode default settings are recommended for in-home use.
ENERGY STAR® qualified.
Retail mode is intended for in-store display and resets video
settings at Power On.
INPUT
TV
AV
Component
VGA
HDMI 1
HDMI 2
HDMI 3
HDMI 4
Hi-DMP
EXIT
Select
Enter
Exit
ENTER
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hisense 50K610GW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hisense 50K610GW in the language / languages: English as an attachment in your email.

The manual is 15,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info