731849

Hikvision DS-6716HUHI-K Manual

63
Zoom out
Zoom in
Previous page
1/91
Next page
DS-6700HUHI-K Series Encoder User Manual
62
Figure 7. 15 Line Crossing Detection
2. Select the Camera.
3. Check the checkbox of Enable Line Crossing Detection to enable the function.
4. Click Area Settings tab and select the line from the drop-down list.
5. Click Draw Area, and a virtual line is displayed on the live video.
6. Drag the line, and you can locate it on the live video as desired. Click on the line, two red squares are
displayed on each end, and you can click-and-drag one of the red squares to define the shape and length of
the line.
7. Select the direction for line crossing detection. And you can select the directions as A<->B, A ->B, and
B->A.
A<->B: The object going across the plane with both directions can be detected and alarms are triggered.
A->B: Only the object crossing the configured line from the A side to the B side can be detected.
B->A: Only the object crossing the configured line from the B side to the A side can be detected.
8. Click Stop Drawing when finish drawing.
9. Drag the slider to set the sensitivity value.
Sensitivity: Range [1-100]. It stands for the percentage of the body part of an acceptable target that goes
across the pre-defined line.
Sensitivity = S1/ST*100
S1 stands for the target body part that goes across the pre-defined line. ST stands for the complete target
body.
Example: if you set the value as 60, the action can be counted as a line crossing action only when 60 percent
or more body part goes across the line.
The Sensitivity of the detection is supported by certain models. Refer to actual display for details.
10. Repeat the above steps to configure other lines. Up to 4 lines can be set. You can click Clear to clear all
pre-defined lines.
11. Click the Arming Schedule tab to set the arming schedule. Refer to Step 6 in Chapter 7.1.1 Configuring
Motion Detection.
12. Click the Linkage Method tab to set the linkage methods. Refer to Step 7 in Chapter 7.1.1 Configuring
Motion Detection.
13. Click Save to save the settings.
7.2.4 Configuring Scene Change Detection
Purpose:
Scene change detection function detects the change of surveillance environment affected by the external factors;
such as the intentional rotation of the camera and some certain actions can be taken when the alarm is triggered.
Steps:
1. Go to Configuration > Event > Smart Event > Scene Change Detection.
… 63 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikvision DS-6716HUHI-K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikvision DS-6716HUHI-K in the language / languages: English as an attachment in your email.

The manual is 3,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info