816244

Hikoki WR36DH Manual

7
Zoom out
Zoom in
Previous page
1/264
Next page
English
7
Slippery handles and grasping surfaces do not allow
for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer.
A charger that is suitable for one type of battery
pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically
designated battery packs.
Use of any other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical
help.
Liquid ejected from the battery may cause irritation
or burns.
e) Do not use a battery pack or tool that is
damaged or modified.
Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion
or risk of injury.
f) Do not expose a battery pack or tool to fire or
excessive temperature.
Exposure to fire or temperature above 130°C may
cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specified in the instructions.
Charging improperly or at temperatures outside the
specified range may damage the battery and
increase the risk of fire.
6) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
b) Never service damaged battery packs.
Service of battery packs should only be performed
by the manufacturer or authorized service providers.
PRECAUTION
Keep children and infirm persons away.
When not in use, tools should be stored out of reach
of children and infirm persons.
CORDLESS IMPACT WRENCH
SAFETY WARNINGS
1. Hold the power tool by insulated gripping
surfaces, when performing an operation where the
fastener may contact hidden wiring.
Fasteners contacting a “live” wire may make exposed
metal parts of the power tool “live” and could give the
operator an electric shock.
ADDITIONAL SAFETY WARNINGS
1. This is a portable tool for tightening and loosening bolts
and nuts. Use it only for these operation.
2. Make sure to securely hold the tool during operation.
Failure to do so can result in accidents or injuries.
(Fig.2)
3. Preparing and checking the work environment. Make
sure that the work site meets all the conditions laid forth
in the precautions.
4. Check the actual tightening torque with a toruqe
wrench.
5. Stop the tool before switching the direction of rotation.
Always release the switch and wait for tool to stop
before switching the direction of rotation.
6. Never touch the turning part. Do not allow the turning
part section to get near your hands or any other part of
your body. You could be cut or caught in the turning
part. Also, be careful not to touch the turning part after
using continuously it for a long time. It gets quite hot
and could burn you.
7. Please use the designated attachments which are listed
in the operations manual and HiKOKI’s catalog.
Accidents or injuries could result from not doing so.
8. Make sure to firmly install the attachments in the anvil. If
the attachments is not firmly installed it might come out
and cause injuries.
9. The power tool is equipped with a temperature
protection circuit to protect the motor. Continuous work
may cause the temperature of the unit to rise, activating
the temperature protection circuit and automatically
stopping operation. If this happens, allow the power tool
to cool before resuming use.
10. The motor may stop in the event the tool is overloaded.
In this should occur, release the tool’s switch and
eliminate the cause of the overload.
Avoid touching the front case which can heat up during
continuous operation.
11. The use of the battery in a cold condition (below 0
degree Centigrade) can sometimes result in the
weakened tightening torque and reduced amount of
work. This, however, is a temporary phenomenon, and
returns to normal when the battery warms up.
12. Do not give a strong shock to the switch panel or break
it. It may lead to a trouble.
13. Do not look directly into the light. Such actions could
result in eye injury.
Wipe off any dirt or grime attached to the lens of the
LED light with a soft cloth, being careful not to scratch
the lens.
Scratches on the lens of the LED light can result in
decreased brightness.
14. Resting the unit after continuous work.
15. Do not touch the hammer case, as it gets very hot
during continuous work.
16. Always charge the battery at a temperature of 0°C–
40°C. A temperature of less than 0°C will result in over
charging which is dangerous. The battery cannot be
charged at a temperature higher than 40°C. The most
suitable temperature for charging is that of 20°C–25°C.
17. Do not use the charger continuously.
When one charging is completed, leave the charger for
about 15minutes before the next charging of battery.
18. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
19. Never disassemble the rechargeable battery and
charger.
20. Never short-circuit the rechargeable battery. Short-
circuiting the battery will cause a great electric current
and overheat. It results in burn or damage to the
battery.
2023/02/01 17:11:58Stylesheet: EU Version: 2023.2.1
WR18DH_C99749071_301_EU
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki WR36DH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki WR36DH in the language / languages: All languages as an attachment in your email.

The manual is 4.21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info