816366

Hikoki WR36DF Manual

13
Zoom out
Zoom in
Previous page
1/244
Next page
13
English
*2 How to use the LED light
To prevent the battery power consumption caused
by forgetting to turn o the LED light, the light goes o
automatically in about 10 seconds.
*3 Tightening mode selector function
CAUTION
Select tightening mode while the trigger switch is
released. Failure to do so could result in malfunction.
NOTE
The appropriate mode will vary depending on the screw
and the material being screwed. Adjust the tightening
mode setting by test-tightening a number of screws.
The tightening mode cannot be changed unless the
rechargeable battery has been mounted in the tool and
the switch has been pulled.
(1) High / Low mode selector switch (Fig. 13)
The tightening mode switches between 4 di erent
rotation speeds each time the High / Low mode selector
switch is pressed.
(2) Auto stop mode selector switch (Fig. 14)
Each time the auto stop mode selector switch is pressed,
the auto stop function will switch between ON and OFF.
High/Low mode setting
Mode 1
600 min-1 Mode 2
900 min-1 Mode 3
1200 min-1 Mode 4
1500 min-1
Auto Stop Time: OFF
USE:
[Mode 1 and 2] For work that requires fi ne adjustments.
[Mode 3] For work that requires the power to be
suppressed.
[Mode 4] For work that requires power and speed.
(3) Auto stop mode (Fig.15)
Stops automatically after a preset time has elapsed.
Push the Push button to the forward (“R”) position, then
press the Auto stop mode selector switch to select the
setting.
Auto stop mode setting
Mode 1
600 min-1 Mode 2
900 min-1 Mode 3
1200 min-1 Mode 4
1500 min-1
Auto Stop Time:
Stops within 1.2 seconds after impact begins.
USE:
[Mode 1] Steel frame temporary tightening, etc.
[Mode 2] Truck wheel nut or piping temporary tightening,
etc.
[Mode 3 and 4] Heavy machinery or bridge girder
temporary tightening, etc.
(4) Auto slow mode (Fig. 16)
Stops for a preset time and/or changes the speed
automatically to a preset speed.
Push the Push button to the reverse (“L”) position, then
press the Auto stop mode selector switch to select the
setting.
Auto slow mode setting
Mode 1
600 min-1 Mode 2
900 min-1 Mode 3
1200 min-1 Mode 4
1500 min-1
[Trigger displacement: Maximum]
Pauses for 0.5 seconds after bolt loosening is detected.
Rotation speed is reduced to 60–350 min-1 depending on
how far the trigger is pulled after restarting.
(Rotation does not stop after restarting.)
[Trigger displacement: Halfway]
Pauses for 0.5 seconds after bolt loosening is detected.
Rotation speed is reduced as follows depending on how
far the trigger is pulled after restarting.
(Rotation does not stop after restarting.)
60–330 min-1 60–500 min-1 60–660 min-1 60–830 min-1
USE:
For work of loosening bolts or nuts.
This function helps prevent nuts from dropping when
loosening them.
NOTE
Depending on factors such as the bolt or nut size, socket
used, and extent of tightening, there is a risk of nuts
accidentally dropping if the nut becomes detached from
the screw thread while the power tool is operating.
MAINTENANCE AND INSPECTION
1. Inspecting the socket
A worn or deformed hex. or a square-holed socket will
not give an adequate tightness to the fi tting between
the nut or anvil, consequently resulting in loss of
tightening torque. Pay attention to wear of a socket holes
periodically, and replace with a new one if needed.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
5. Cleaning on the outside
When the tool is stained, wipe with a soft dry cloth or
a cloth moistened with soapy water. Do not use chloric
solvents, gasoline or paint thinner, for they melt plastics.
0000BookWR36DF.indb130000BookWR36DF.indb13 2022/10/1618:10:502022/10/1618:10:50
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki WR36DF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki WR36DF in the language / languages: All languages as an attachment in your email.

The manual is 29.81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info