816254
20
Zoom out
Zoom in
Previous page
1/192
Next page
20
English
The declared vibration total value has been measured in
accordance with a standard test method and may be used
for comparing one tool with another.
It may also be used in a preliminary assessment of exposure.
WARNING
The vibration emission during actual use of the power
tool can di er from the declared total value depending in
the ways in which the tool is used.
Identify safety measures to protect the operator that
are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is
switched o and when it is running idle in addition to the
trigger time).
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your
dealer or the HiKOKI Authorized Service Center.
1. Power tool
Symptom Possible cause Remedy
Does not move No battery remaining. Charge the battery.
Battery is not properly installed. Push battery in until a click is heard.
The tool remains in reverse-rotation mode Press the Manual Mode switch to cancel
reverse-rotation.
Suddenly stopped Overload protection circuit activated. Remove cause of overload.
Heat protection circuit activated due to
overheating of the battery or the tool itself. Allow battery and tool to fully cool down.
Switch cannot be pulled Insu cient pressure on the switch lock. Press switch lock in until it comes to the
end.
Hear a “beep” when pulling
on the switch Switch is pulled in a small amount. Not a problem.
Pull harder on the switch and the sound will
stop.
Cannot cut satisfactorily Cutter is worn/degraded/damaged Replace with a new cutter.
Working tool outside of its normal capacity
(material, material diameter, processing
quantity).
Review “SPECIFICATIONS” to cut properly.
Have trouble holding rebar
when cutting Grip rubber is worn. Replace with new grip rubber.
Contact a HiKOKI Authorized Service
Center.
Cannot bend properly Working tool outside of its normal capacity
(material, material diameter, processing
quantity).
Review “SPECIFICATIONS” to bend
properly.
Cannot install battery Attempting to install battery other than type
speci ed. Use Multi Volt type battery.
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
0000BookVB3616DA.indb200000BookVB3616DA.indb20 2023/02/1715:02:592023/02/1715:02:59
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki VB3616DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki VB3616DA in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6.73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info