742714

Hikoki UM 36DA Manual

13
Zoom out
Zoom in
Previous page
1/256
Next page
13
English
(*1) Removing and inserting the battery
NOTE
Ensure that the battery cover is securely closed unless
you are removing or installing the battery.
If any water, concrete, or dust enters the body of the
power tool or the terminals of the battery, a failure may
occur.
(*2) Low-speed / High-speed changeover
CAUTION
Avoid mixing viscous materials in Mode 2 (High speed).
The motor will stop if it detects an excessive load.
Overloading may damage the tool.
To change speed, rotate the shift lever as indicated by the
arrow. The numeral “1” engraved on the machine body
denotes low speed, the numeral “2” denotes high speed.
If it is hard to turn the shift lever, turn the shaft slightly in
either direction and then turn the gear shift lever again.
NOTE
○ Align the arrow on the shift lever to one of the numbered
positions.
Use with the shift lever set between the numbered
positions may damage the tool.
○ Rotate the shift lever only when the motor is not
operating.
Changing the shift lever position while the motor is
running may damage the tool.
Mode
Mode 1
(Low speed)
Mode 2
(High speed)
Rotation
speed
0 – 500 min
-1
0 – 1200 min
-1
Usage
High viscosity
materials
(e.g., mortar or
leveling mortar)
Low viscosity
materials
(e.g., paint)
(*3) Mounting and dismounting of the holder
Attached to the main unit when packing.
(*4) Mounting of the screw
CAUTION
Take extreme care to avoid injury when mounting or
detaching the mixing screw.
(*5) How to use
NOTE
○ Ensure that the mixing container is placed in a fi rm and
secure position.
A container that is not properly secured may move
unexpectedly.
○ Place the mixing screw inside the container and check
for safety before turning on the switch.
Once mixing is complete, wait for the mixing screw to
come to a complete stop before removing it from the
container.
○ Start mixing at low speed. Assess mixing status before
adjusting the speed.
MAINTENANCE AND INSPECTION
CAUTION
Be sure to turned off the switch and remove the battery
before maintenance and inspection.
1. Mixing screw cleaning
To extend the life of the screw and shaft, clean by
washing in water after use.
CAUTION
Do not leave the tool with the mixing screw immersed in
plaster.
Doing so may result in corrosion and fl aking of the screw
surface and plaster contamination.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
5. Cleaning on the outside
After using the power tool, wipe the tool body (in
particular, the ventilation holes, areas around the switch
trigger, and areas near the edges of the covers require
careful wiping) to remove any concrete using a cloth that
is soaked in a soap solution and well wrung.
Do not use gasoline, thinner, benzine, or kerosene as
they can dissolve plastics.
Immediately remove any concrete that has become
attached to the fl exible assembly.
6. Storage
Store the power tool in a place in which the temperature
is less than 40°C and out of reach of children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signifi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, signifi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to fi ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
Important notice on the batteries for the HiKOKI
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used with
batteries other than these designated by us, or when
the battery is disassembled and modifi ed (such as
disassembly and replacement of cells or other internal
parts).
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country specifi c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
to a HiKOKI Authorized Service Center.
0000Book_UM36DA_EU.indb 130000Book_UM36DA_EU.indb 13 2020/07/03 10:33:112020/07/03 10:33:11
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki UM 36DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki UM 36DA in the language / languages: All languages as an attachment in your email.

The manual is 9,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info