816276
8
Zoom out
Zoom in
Previous page
1/148
Next page
8
English
5. Hold the charger rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used, the
pilot lamp of the charger lights for 1 second, does not
light for 0.5 seconds (o for 0.5 seconds). In such a case,
rst let the battery cool, then start charging.
When the pilot lamp ickers (at 0.2-second intervals),
check for and take out any foreign objects in the charger’s
battery connector. If there are no foreign objects, it is
probable that the battery or charger is malfunctioning.
Take it to your authorized Service Center.
Since the built-in micro computer takes about 3 seconds
to con rm that the battery being charged with charger
is taken out, wait for a minimum of 3 seconds before
reinserting it to continue charging. If the battery is
reinserted within 3 seconds, the battery may not be
properly charged.
MOUNTING AND OPERATION
Action Figure Page
Inserting the battery 2-a 2
Removing the battery 2-b 2
Charging 3 2
Turning the work light on*142
Changing the angle of the work light 5 3
Mounting on a wall for use 6 3
Securing to a tripod*273
Remaining battery indicator*383
Charging a USB device*493
Selecting accessories 139
*1 When the brightness reaches the maximum (4000 lm) or
the minimum (700 lm), the light brie y blinks twice.
*2
NOTE
When using a tripod, ensure that it is stable so that it
does not fall over.
*3
State of lamp Battery Remaining Power
Over 80%
60%–80%
40%–60%
20%–40%
Less than 20%
When the remaining battery becomes low, the light brie y
blinks about once every 3 minutes.
As the remaining battery indicator shows somewhat
di erently depending on ambient temperature and battery
characteristics, read it as a reference.
NOTE
When using a Multi-volt battery, please refer to the
indicator lamp on the battery for the battery remaining
power.
Do not give a strong shock to the panel or break it. It may
lead to a trouble.
*4
NOTE
If the remaining battery becomes low, USB output is
automatically stopped, and the work light cannot charge
USB devices.
The charging time di ers depending on the type of USB
device being used.
Do not use for any purpose other than charging a USB
device.
(Refer to “USB DEVICE CONNECTION
PRECAUTIONS”.)
MAINTENANCE AND INSPECTION
WARNING
When not using the work light for a long time, performing
maintenance on it, inspecting it, or storing it, be sure to
turn OFF the switch and pull out the battery.
1. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
2. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
3. Cleaning on the outside
When the cordless work light is stained, wipe with a soft
dry cloth or a cloth moistened with soapy water.
Do not use chloric solvents, gasoline or paint thinner, for
they melt plastics.
4. Storage
Store the cordless work light and the battery in a place in
which the temperature is less than 40°C and out of reach
of children.
00BookUB18DC.indb800BookUB18DC.indb8 2023/05/2510:08:422023/05/2510:08:42
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki UB18DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki UB18DC in the language / languages: All languages as an attachment in your email.

The manual is 6.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info