816370

Hikoki SV1813DA Manual

10
Zoom out
Zoom in
Previous page
1/184
Next page
10
English
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used,
the pilot lamp of the charger lights up green or lights
for 1 second, does not light for 0.5 seconds (off for
0.5 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the pilot lamp fl ickers in red (at 0.2-seconds
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
MOUNTING AND OPERATION
Action Figure Page
Removing and inserting the battery*122
Charging 3 2
Installing the sanding paper*242
Attaching the dust bag*353
Switch operation 6 3
Adjustment of speed*473
How to hold the random orbit sander 8 3
How to move the random orbit
sander*593
Installing the selecting accessories 10 4
Attaching the dust collector 11 4
Selecting accessories ―178
*1 Removing and inserting the battery
CAUTION
Before installing or removing the battery, turn the switch
to the OFF position.
If the battery is inserted with the switch in the ON
position, the motor will operate unexpectedly.
*2 Installing the sanding paper
Since the attachment is a hook-and-loop type, the
sanding paper can be installed easily by just pressing it
onto the pad. Gently pinch and hold together two places
on the edges of the sanding paper so that two holes are
visible on the bottom. (Fig. 4-a)
Overlap the two holes of the sanding paper with two
holes of the pad, and attach the whole surface of the
sanding paper to the pad so that the remaining holes are
also aligned. (Fig. 4-b)
*3 Attaching the dust bag
If too much dust accumulates in the dust bag, the dust
collection power will be reduced.
Dispose of dust as soon as possible.
*4 Adjustment of speed
The sander is equipped with an electric control circuit that enables speed control. To adjust the speed, turn the dial
shown in Fig. 7. When the dial is set to “1”, the sander operates at the minimum speed (7000 min-1). When the dial set
to “6”, the sander operates at the maximum speed (11000 min-1). Adjust the speed according to the material to be cut
and working effi ciency.
Material Grain Dial scale
Rough grinding Fine grinding
Paintwork:
Sanding
Repairs
(scratches, rust spots)
Stripping
180
120
40
400
240
80
3–6
2–4
2–4
Wood:
Softwood
Hardwood
Veneers
60–80
60
240
240
180
320
3–6
3–5
2–4
Metals:
Aluminium
Steel
Stainless steel
80
60
120
240
240
240
2–4
3–6
3–6
Note: Please use this table as a standard.
*5 How to move the random orbit sander
CAUTION
○ Immediately after use, always ensure that the switch is in
the OFF position and pull out the battery.
○ Since the sander may suck in dust and debris, be careful
not to place it where there is much dust and debris when
it is still spinning right after use.
○ Looking from above, the sanding pad rotates clockwise
during the loaded operation, but it may rotate
counterclockwise during the no-load operation.
○ Never run the tool without the sanding paper. You may
seriously damage the pad.
○ Using the tool with the pad edge contacting the
workpiece may damage the pad.
NOTE
Movement of the sander may tend to become unsteady
after new sanding paper has been installed, because of
the new, coarse grain of the paper. This can be avoided
by slightly tilting the sander forward or backward during
sanding or polishing. Sander movement will become
steady as the sanding paper surface becomes properly
abraded.
0000BookSV1813DA.indb100000BookSV1813DA.indb10 2022/02/169:50:382022/02/169:50:38
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki SV1813DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki SV1813DA in the language / languages: All languages as an attachment in your email.

The manual is 11.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info