816323
13
Zoom out
Zoom in
Previous page
1/228
Next page
13
English
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (o for
0.3 seconds). In such a case, rst let the battery cool,
then start charging.
When the charge indicator lamp ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
MOUNTING AND OPERATION
Action Figure Page
Removing and inserting the battery*122
Charging 3 2
Installing the sanding belt*243
How to use the dust bag*353
How to use the elbow*463
Switch operation 7 4
About the mode change function*584
How to adjust sanding belt position*694
How to hold and move the belt
sander*710 4
How to work on corner 11 4
Attaching the dust collector 12 5
Remaining battery indicator 13 5
Charging a USB device from an
electrical outlet 16-a 5
Charging a USB device and battery
from an electrical outlet 16-b 5
How to recharge USB device 17 6
When charging of USB device is
completed 18 6
Selecting accessories 218
*1 Removing and inserting the battery
CAUTION
Before installing or removing the battery, turn the switch
to the OFF position.
If the battery is inserted with the switch in the ON
position, the motor will operate unexpectedly.
*2 Installing the sanding belt
Align the arrow on the inside of the sanding belt with the
direction of the mark on the tool and install it.
CAUTION
Use only sanding belt size speci ed on the product
nameplate.
Sanding belt installed in the wrong direction will lower
work e ciency and shorten life of sanding belt.
Avoid pinching your ngers when opening and closing
the lever.
NOTE
The drive pulley and idle pulley will be hot after use.
Use an air blow gun or similar device to remove any
debris from around the pulleys with the sanding belt
removed.
*3 How to use the dust bag
WARNING
Clean the dust bag before and after sanding metal, and
remove any sanding dust from inside. Metal sanding
dust can cause res.
*4 How to use the elbow
Adjust the angle of the elbow so that the dust is
discharged away from your body.
*5 About the mode change function
The unit has “Transmission mode” and “Auto mode”.
With Transmission mode, the belt sander's number of
revolutions can be set at one of ve stages.
When operating in Transmission mode, the set number
of revolutions will be maintained regardless of changes
in load.
With Auto mode, you can lower noise and vibration by
lowering the maximum number of revolutions while in a
no-load state.
While in Auto mode, the number of revolutions will be
raised if the load becomes greater during operation.
On the other hand, the number of revolutions will be
lowered if the load decreases during operation. (Table 3)
Set the mode and dial according to work application.
Table 3
Dial setting Belt speed
1 122 m/min
2 220 m/min
3 310 m/min
44
0
0 m/min
5 450 m/min
A122 m/min (No load)
45
0
m/min (With load)
00BookSB3608DAEU.indb1300BookSB3608DAEU.indb13 2022/08/0514:20:492022/08/0514:20:49
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki SB3608DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki SB3608DA in the language / languages: All languages as an attachment in your email.

The manual is 10.57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info