816356
24
Zoom out
Zoom in
Previous page
1/420
Next page
24
English
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your
dealer or the HiKOKI Authorized Service Center.
PROBLEM CHECK METHOD CORRECTION
Power switch doesn’t turn on.
Turn on once, but turn o
automatically.
Low battery charge. Charge the battery.
Damaged internal electronics. Contact HiKOKI for replacement.
Push lever and/or trigger is ON state ? Keep push lever and trigger in OFF state.
Keep no operation over 30 minutes ?
(Auto-power o function) Push and hold power switch more than 1
second to switch “ON”
Nailer doesn’t operate
(Power switch ON). Nailer not enough pressed against
workpiece. Hold nailer rmly and press to the
workpiece completely.
Trigger not enough pulled. Pull the trigger rmly.
More than 2 seconds pass from push
lever ON to trigger ON (or trigger ON to
push lever ON).
Make sure that less than 2 seconds pass
between push lever ON and trigger ON (or
between trigger ON and push lever ON).
Preventive mechanism activated.
(No nails, or too few fasteners remaining)
(excluding NT1850DBSL)
Reload the nails into magazine.
Switch lock lever (Trigger lock function) is
“ON” position. Set Switch lock lever to “OFF” position.
(Refer to Fig. 8)
Machine is too cold (below -5°C) or too
hot. (LED light blinks at regular intervals,
and power switch goes o after 10
seconds.) (Refer to page 18)
Allow the nailer to cool or warm-up
throughly in adequate condition.
Damaged internal electronics. Contact HiKOKI for replacement.
Nailer operates, but no nail is
driven. Magazine is dirty. Blow and wipe clean the magazine.
Check for a jam. Clear a jam (refer to Fig. 26, 27).
Driver blade worn or damaged? Contact HiKOKI for replacement.
Ribbon spring weakened or damaged? Replace ribbon spring.
Nail feeder damaged? Replace nail feeder.
Check for proper nails. Use only recommended nails.
Weak drive.
Slow to cycle. Check position of nailing depth adjustment
adjuster. Readjust according to Fig. 19, 20.
Driver blade worn? Contact HiKOKI for replacement.
Compressed air pressure has become
low. Contact HiKOKI for replacement.
Damaged internal electronics. Contact HiKOKI for replacement.
Drives too deep. Check position of nailing depth adjustment
adjuster. Readjust according to Fig. 19, 20.
Skipping nails.
Intermittent feed. Check for proper nails. Use only recommended nails.
Nail feeder damaged? Replace nail feeder.
Ribbon spring weakened or damaged? Replace ribbon spring.
Driver blade worn or damaged? Contact HiKOKI for replacement.
Nails jam.
Driven nail is bent. Check for proper nails. Use only recommended nails.
Driver blade worn or damaged? Contact HiKOKI for replacement.
Remaining battery indicator on
the machine doesn’t match to
battery Refer to the indicator lamp on the battery.
000BookNT1865DBAL.indb24000BookNT1865DBAL.indb24 2022/06/2911:54:392022/06/2911:54:39
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki NT1865DBAL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki NT1865DBAL in the language / languages: All languages as an attachment in your email.

The manual is 38.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info