816326
17
Zoom out
Zoom in
Previous page
1/332
Next page
17
English
(1) Intermittent operation (Trigger re)
Use the SINGLE SEQUENTIAL ACTUATION
MECHANISM setting. (See Fig. 12)
WARNING
For intermittent operation, Set the nailing operation
switch to SINGLE SEQUENTIAL ACTUATION
MECHANISM (Nailing operation indicator is light in
blue.) (i.e. Set to SINGLE ACTUATION MECHANISM.)
To avoid double ring or accidental ring due to recoil.
1) Set to SINGLE SEQUENTIAL ACTUATION
MECHANISM.
2) Pull the trigger rapidly and rmly.
Set the nailing operation switch to SINGLE SEQUENTIAL
ACTUATION MECHANISM (Nailing operation indicator
is light in blue.)
Position the nail outlet on the workpiece with nger o
the trigger.
Depress the push lever rmly until it is completely
depressed.
Pull the trigger to drive a nail.
Remove nger from the trigger and lift the tool o the
wood surface completely.
To continue nailing in a separate location, move the nailer
along the wood, repeating steps as required.
NOTE
Operations
and should be done within 4 seconds
of each other. If more than 4 seconds pass after , the
Nailer will not work properly. If this happens, retry from
.
(2) Continuous operation (Push lever re)
Using CONTACT ACTUATION MECHANISM (See
Fig. 13)
WARNING
To avoid double ring or accidental ring due to recoil.
1) Do not press the nailer against the wood with
excessive force.
2) Separate the nailer from the wood as it recoils after
nailing.
Set the nailing operation switch to CONTACT
ACTUATION MECHANISM (Nailing operation indicator
is blink in blue.)
Pull the trigger with the Nailer o the workpiece.
Depress the push lever against the workpiece to drive a
nail.
Move the Nailer along the workpiece with a bouncing
motion.
Each depression of the push lever will drive a nail.
As soon as the desired number of nails have been driven,
remove nger from the trigger.
NOTE
Operations
and should be done within 2 seconds
of each other. If more than 2 seconds pass after , the
Nailer will not work properly. If this happens, retry from
.
WARNING
Keep your nger o the trigger except during nailing
operation, because serious injury could result if the push
lever accidentally contacts you or others in work area.
Keep hands and body away from the discharge area.
This HiKOKI nailer may bounce from the recoil of driving
a nail and unwanted subsequent nail may be driven,
possibly causing injury.
NOTE
If all warnings and instructions are followed, safe
operation is possible with all two systems: SINGLE
SEQUENTIAL ACTUATION MECHANISM, CONTACT
ACTUATION MECHANISM.
Always handle nails and package carefully. If nails are
dropped, collating bond may be broken, which will cause
mis-feeding and jamming.
After nailing:
1) remove battery from the Nailer;
2) remove all nails from the Nailer;
2. Adjusting the nailing depth
To assure that each nail penetrates to the same depth,
be sure that the Nailer is always held rmly against the
workpiece.
If nails are driven too deep or shallow into the workpiece,
adjust the nailing in the following order.
Remove the battery from the Nailer.
If nails are driven too deep, turn the adjuster to the
shallow side. (See Fig. 14)
Adjustments are in half-turn increments.
If nails are driven too shallow, turn the adjuster to the
deep side. (See Fig. 15)
Stop turning the adjuster when a suitable position is
reached for a nailing test.
Connect the battery to the Nailer.
ALWAYS WEAR SAFETY GLASSES.
Perform a nailing test.
Remove the battery from the Nailer.
Choose a suitable position for adjuster.
3. Using the hook (See Fig. 16)
WARNING
When using the hook, turn o the power switch (green
light “OFF”). Pay su cient attention so that the main
equipment does not fall.
If the tool falls, there is a risk of accident.
Hook can be installed on the left or right side.
Remove the battery, then remove all remaining nails
from the magazine.
Securely hold the main unit and remove the screw using
a screwdriver.
Remove the hook.
Install the hook on the other side and securely fasten
with screw.
NOTE
Hook can be used as a hanger.
4. Using the nose cap (See Fig. 17)
WARNING
When attaching or detaching the nose cap, be sure
to remove your nger from the trigger and remove all
remaining fasteners and the battery from the nailer.
If you like to protect the surface of workpiece against
scratches or markings made by the push lever, attach the
accessory nose cap to the push lever.
Remove all remaining fasteners and battery from nailer.
Put the nose cap to the toe of the push lever.
When not using the nose cap, secure in the storage
compartment located on the reverse side of the
magazine.
NOTE
The nose cap may reduce nailing depth due to its
thickness. Re-adjustment of nailing depth is required.
5. Clearing a jam
If nails are jammed in ring head, remove it, and adjust
the nailing in the following order.
CAUTION
Remove the battery from the Nailer.
Remove the battery from the Nailer.
Remove all nails.
Release the Lock lever and open guide plate. (See
Fig. 18)
Remove the jammed nail with a slotted-head screwdriver.
(See Fig. 19)
CAUTION
NEVER hit the driver blade.
NEVER point the tool at yourself or another person, to
avoid risk of injury by mis- ring.
Even if the battery is removed from the nailer, there is still
energy of compressed air remaining inside.
0000BookNT1850DA.indb170000BookNT1850DA.indb17 2022/09/0814:45:002022/09/0814:45:00
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hikoki NT1850DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hikoki NT1850DA in the language / languages: All languages as an attachment in your email.

The manual is 25.59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info